User: 82angelfan, Location: Hesperia, Ca
Asked on: Tuesday, October 7, 2025 at 9:28 am EDT
Answered on: Tuesday, October 7, 2025 at 9:29 am EDT
Question: Please help explaining problem to owner.Private Surgery center, 3 ORs. See attached Picasso Style drawing.We built a private surgery center with three identical ORs. Each OR has an Isolation panel that is a combination normal power, critical power, separate feeds from critical system and normal system.The panel is fed with Single Phase 480V 30amp to a 2pole main that then feeds a step down transformer to 120V. Neither coil is grounded, though the can and the branch circuits are attached to a ground bus, that jumpers both have per NFPA99 and 517 in code book. The Neutral from the secondary is completely Isolated. I believe this creates an ungrounded Neutral. The Secondary feeds a single phase panel, where A is 120 hot and B is Neutral. All branch circuits are fed from 2 pole 20 AMP breakers. There is a LIM module in the panels that monitors voltage, and more importantly leakage. Each OR also has a completely Isolated DATA system with Router, Switch box, and computer, linked to Monitors, booms, and data ports. All of this equipment is in a cabinet and plugged into a power supply similar to those used in IDF racks.When using a meter, I get 124V hot to neutral, but a combination of that voltage from hot to ground and neutral to ground at the receptacles. When I plug in my Greenlee plug tester it reads OPEN GROUND.My problem arises in only one OR. OR1 works the same as described above until that OR's Router AND switch box are plugged in. It has to be both, each has their own power supply. When plugged in, my greenly tester now reads as "good ground", both yellow lights on, but leakage voltage now RAMPS UP until alarm sounds on LIM. It only does this on critical side, so I am assuming the voltage is leaking through the neutral, not the ground. It also dues not RAMP UP UNTIL I PLUG IN MY TESTER at any critical receptacle or circuit.I have checked all my connections, the issue is isolated to that one circuit that powers the data equipment but bleeds in to the other circuits. I have plugged the suspected equipment into a different circuit with same result.Does anyone have any insight to what could be causing this. I am convinced the power supply has an issue, but could be the router or switch box. Why would the issue only happen when BOTH are plugged into the power supply. If one or the other is plugged directly into the wall, there is no issue.
Okay, here's an explanation you can use to discuss this with the owner of the surgery center, breaking down the problem and potential causes in a way that's hopefully understandable.
Subject: Urgent Issue with Electrical System in Operating Room 1"As you know, we've been very careful to follow all electrical codes and safety standards in setting up our operating rooms. Recently, we've discovered a problem in Operating Room 1 (OR1) that requires immediate attention because it affects the safety of our electrical system."1. Understanding the System (Keep it brief and avoid technical jargon where possible)
"Our ORs have a special electrical system designed to prevent electric shock during surgery. This is especially important since we use a lot of sensitive equipment directly on or near patients. Instead of a standard grounded system, we use an isolated power system. Think of it like this: instead of having one wire firmly connected to the ground to make a complete circuit, neither of the wires is directly grounded. We need to keep this system free from grounding to prevent a shock." "This isolated power system has a device called a Line Isolation Monitor (LIM). This device constantly monitors the electrical system for any leakage of current to ground. If there's a leak, the LIM sounds an alarm, warning us of a potential problem."
2. The Problem
"In OR1, we've identified a situation where plugging in specific equipment – the router and switch box for the data network that manages monitors and data ports – causes the LIM to sound an alarm." "Here's the sequence: The electrical system in OR1 appears normal until both the router and switch box are plugged into a specific power supply within the system. Once both are plugged in, and a simple receptacle tester is plugged into any receptacle, the LIM starts showing a leakage current, gradually increasing until the alarm goes off. This indicates that electricity is somehow leaking to ground, which shouldn't be happening in our isolated system. Plugging in the tester, is simply amplifying an already existing problem." "Significantly, this only happens when both devices are connected to that power supply and a tester is plugged in. If only one device is plugged into the power supply, or if the devices are plugged directly into a standard wall outlet, the problem doesn't occur." "Also this problem only arises when the critical power is being tested, and not when normal power is tested, suggesting the fault is there." "The fact that a receptacle tester needs to be plugged in, suggests a larger problem is there, just not quite large enough to cause the system to alarm. It could be that by plugging in the tester, you are completing the circuit in some fashion to cause the alarm to sound."
3. What This Means (The Importance)
"This leakage current could indicate a fault in the system that could compromise the isolation we rely on to protect patients from electrical shock. While there are multiple systems in place to keep the patient safe, the potential exists to expose patients to a higher current if there is no isolation.
4. Potential Causes (This is where you show you've investigated)
"We suspect that the power supply used by the router and switch box is the most likely source of the problem. While it seems to work, it may have an internal fault that causes a slight leakage of current to ground when both devices are connected. Also, there may be a common path or part in each device, when combined are causing the issue." "It's also possible that one of the network devices (the router or switch box) has an internal fault, but only reveals itself when connected to the specific power supply. The other devices could be causing noise on the circuit, which becomes worse in the power supply as you add more devices."
5. Next Steps (and potential Costs)
Immediate Action
"We need to immediately stop using this power supply and network equipment in OR1 until we can identify and fix the problem.
Troubleshooting
"We'll need to bring in a qualified electrical engineer or technician experienced with isolated power systems to conduct a thorough investigation. This would likely involve: Testing the power supply with specialized equipment. Testing the router and switch box individually and together. Examining the wiring and connections within the OR1 electrical system." "There may also be a testing lab that can perform hipot testing on each device to further isolate any potential problems."
Resolution
"Depending on the cause, the fix could involve: Replacing the faulty power supply. Repairing or replacing a defective router or switch box. Correcting a wiring issue within the OR1 electrical system. "Until we find the source, it is impossible to provide a good estimate of the cost. If you wish to replace all devices at once, a new isolated power supply will run between $1,000 and $3,000. A new router will range from $500 to $1,000, and a switch box will range from $200 to $500."
6. Request
"I recommend that we immediately contact a qualified electrical engineer to assess the situation. I will obtain quotes from reputable companies with experience in medical electrical systems."
Key Points to Emphasize to the Owner
Patient Safety
This isn't just a technical glitch; it could potentially compromise patient safety.
Compliance
Maintaining a properly functioning isolated power system is critical for meeting regulatory requirements and avoiding potential legal issues.
Urgency
Delaying action could lead to a more serious problem or, worse, an incident.
Why this approach works
Clarity
Uses straightforward language, avoiding excessive technical jargon.
Focus on Impact
Highlights the potential consequences of the problem.
Structured Approach
Presents the issue, potential causes, and proposed solutions in a logical manner.*
Empowering: Presents the owner with clear options and a path forward.Remember to be prepared to answer the owner's questions and to provide them with any additional information they may need. Good luck! Flag for review