Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Off grid house bonding sanity check

User: electrofelon, Location: Cherry Valley NY, Seattle, WA

Asked on: Tuesday, October 7, 2025 at 11:50 am EDT
Answered on: Tuesday, October 7, 2025 at 11:50 am EDT

Question: Lets say I have an off grid house (no utility source). There is an outside generator, and a PV system on the roof of the house. Basically I just treat it the exact same as if the generator were a customer owned outdoor transformer, right? So assuming the generator has a breaker integral to it, I would have a system bonding jumper at the genset, and run 4 wire to the house, right? IF applicable, I could use 250.30(A)(1) exception #2 and run 3 wire to the house, and make another N-G bond at the house. But there would always be N-G bond at the genset, and electrodes there. Is that all correct and are there any other options?

Okay, let's break this down and make sure we're on the same page regarding grounding and bonding for your off-grid system with a generator and PV system. You're on the right track, but some nuances need clarification.

Your Understanding (Mostly Correct)



Treating Generator Like a Utility Transformer

Yes, in many ways, that's the correct way to think about it
from a grounding and bonding perspective. The generator becomes the separately derived system (SDS).

Generator Breaker

Assuming the generator has an integral overcurrent device (breaker), that's good and simplifies things.

System Bonding Jumper at the Genset



Yes, absolutely.
This is essential for creating the separately derived system. The System Bonding Jumper (SBJ) connects the neutral conductor to the generator's frame (which is connected to ground). 4-Wire to the House

Generally, yes, running a 4-wire (L1, L2, Neutral, Ground) is the preferred and safest method. This keeps the neutral and ground paths separate downstream of the generator.

250.30(A)(1) Exception #2

You
can use this exception, but it's not generally recommended for an off-grid house. This exception allows you to eliminate the grounding electrode system at the generator location. Instead, you'd run only 3 wires (L1, L2, and Neutral/Grounded Conductor) to the house and establish the grounding electrode system and the system bonding jumper at the house.

Always N-G Bond at Genset (If Running 4-Wire)

Yes, if you are running a 4-wire system, there MUST be an N-G bond at the generator, and the grounding electrode conductor must originate from the generator.

Electrodes at Genset

Yes, if you're running a 4-wire system, the generator must have a grounding electrode system (ground rods, ground ring, etc.) connected to it.

Clarifications, Corrections, and Other Options


Why 4-Wire is Generally Preferred

The primary reason to run 4-wire is to keep fault current away from the neutral conductor downstream. A fault anywhere in the house will have a dedicated ground path back to the generator, tripping the breaker faster and more safely. With 3-wire, a ground fault would travel on the neutral conductor, potentially creating voltage on metal enclosures and appliances.2.

Exception #2 (3-Wire) Considerations



Risk

The 3-wire approach, while code-compliant under the exception, can introduce some risks. A fault on the neutral conductor upstream of the house grounding electrode system could energize the grounding system at the house.

Suitability

I generally would
not recommend using the 3-wire exception (250.30(A)(1) Exception #2) for a dwelling unit. If you have to, I suggest using a neutral/ground fault interrupter at the generator to protect against excessive current flow on the neutral that could come from a fault to ground. This would likely be an unusual situation but possible.3.

Grounding Electrode System at the House (Even with 4-Wire)

It is still common practice to have a grounding electrode system at the house whether or not you use the 3 or 4-wire system. So it is probably safest to have an electrode at both the house, and the generator, even if you run a 4-wire system to the house.4.

Grounding Electrode System Sizing

The size of the grounding electrode conductor (GEC) from the generator to the ground rods is based on the
size of the derived phase conductors from the generator, not the generator's breaker size. Consult Table 250.66. For the house electrodes, the GEC size is based on the size of the ungrounded conductors feeding the building.
5.


Surge Protection

Because you have a separately derived system, it is a great idea to have a surge protective device located as close to the generator as possible.6.

PV System Grounding

Don't forget your PV system! The PV system should have its own grounding electrode system connected to the modules, inverters, and any other relevant equipment. This grounding electrode system is connected separately from the generator's grounding electrode system. It is very important that the frames of all of the PV modules are bonded together and that there is a properly sized conductor from the PV array to the service panel.7.

Automatic Transfer Switch (ATS)

You haven't mentioned an Automatic Transfer Switch (ATS), but it's crucial for seamless switching between the generator and PV (via inverters and battery backup if you have them). Ensure the ATS is properly rated and installed, and that it doesn't accidentally connect the neutral from the generator to the neutral from the inverter, or the utility line, if any.8.

Islanding Protection

You need to make sure your inverters have anti-islanding protection, so that if the grid goes down, the inverters automatically disconnect from the grid and stop feeding power into the grid.

In Summary

For your off-grid home, the
safest and most robust approach is:

4-Wire System

Run a 4-wire (L1, L2, N, Ground) from the generator to the house panel.

SBJ at Generator

Ensure a system bonding jumper connects the neutral to the generator frame (and thus to ground).


Grounding Electrode System at Generator

Install a proper grounding electrode system (ground rods, etc.) at the generator, connected to the generator frame.

Grounding Electrode System at House

Grounding electrode system at the house panel, whether you use a 3 or 4 wire system.


Properly Sized Conductors

Size all conductors (including grounding conductors) according to the NEC.

PV System Grounding

Thoroughly ground the PV system.


Surge Protection:
Install proper surge protection.While the 3-wire system is permissible, the added safety of a separate ground conductor in a 4-wire system makes it the superior choice, especially for a dwelling unit.Consult a qualified electrician familiar with off-grid systems to perform the installation and ensure it complies with all applicable codes. This is not a DIY project! Incorrect grounding and bonding can be extremely dangerous. Flag for review

Previous Question Next Question