User: Bodie-Electric, Location: Sacramento, CA
Asked on: Tuesday, October 7, 2025 at 12:06 pm EDT
Answered on: Tuesday, October 7, 2025 at 12:14 pm EDT
Question: I'm installing a new 22kw Generac with an ATS for this house and am curious what people's opinion is on the best workmanship to pipe between the meter/ats/panel. I'm new to the area and haven't come across this just yet and have a few different opinions on how to do it. I'm just curious if there's a "standard" way to do this and I'm just not seeing it. Thank you.https://imgur.com/a/rWPDrny
Okay, I understand. You're installing a 22kW Generac generator with an automatic transfer switch (ATS) and you're looking for best practices for the conduit runs connecting the meter, ATS, and main electrical panel. You're seeking a "standard" or preferred method for this type of installation, especially considering you're new to the area.
General Considerations and Best Practices
NEC and Local Codes are Paramount
This is the MOST important thing. Everything I'm about to describe must comply with the National Electrical Code (NEC) and any local amendments or regulations your jurisdiction has. Get to know your local inspector and be prepared to follow their guidance. Code adherence trumps everything else.
Permitting
Ensure you have the necessary permits before starting work. The inspector will likely want to see the whole installation.
Professionalism
A clean, well-organized installation is not just aesthetically pleasing; it demonstrates competence and makes future troubleshooting much easier.
Common Conduit Piping Methods (with Pros and Cons)
Here are a few methods, along with their pros and cons. The "best" one depends on your specific site conditions, budget, and local code requirements.1.
Rigid Metal Conduit (RMC)
Description
Heavy-gauge, threaded steel conduit. Requires specialized tools for cutting, threading, and bending.
Pros
Maximum physical protection for conductors. Excellent grounding path. Longest lifespan. Can be used indoors or outdoors, exposed or buried (check with local code) Offers the best protection against physical damage (vehicular traffic, etc.).
Cons
Most expensive option. Most labor-intensive to install. Requires specialized tools. Can be difficult to bend accurately in tight spaces. Heaviest option.
Typical Uses
Locations where physical protection is critical (e.g., near driveways, in areas subject to impact), areas requiring maximum grounding reliability, and installations exposed to corrosive environments (use galvanized RMC).2.
Intermediate Metal Conduit (IMC)
Description
Similar to RMC, but with a thinner wall. Still threaded.
Pros
Good balance of protection and cost. Lighter than RMC, making it easier to work with. Acceptable grounding path. Can be used indoors or outdoors (check with local code).
Cons
More expensive than EMT. Requires threading tools. Not as robust as RMC.
Typical Uses
Similar to RMC, but in applications where the extra strength of RMC isn't strictly necessary. A good compromise in many situations.3.
Electrical Metallic Tubing (EMT)
Description
Thin-walled steel conduit, typically connected using compression or set-screw fittings. Can be bent relatively easily with a conduit bender.
Pros
Least expensive metal conduit option. Lightweight and easy to work with. Can be bent easily.
Cons
Less physical protection than RMC or IMC. Grounding relies on fittings being properly tightened and maintained (use grounding bushings where required). Not suitable for direct burial (unless specifically listed for it). More susceptible to damage.
Typical Uses
Indoor applications, protected outdoor locations, where physical protection is not a primary concern. Often used for residential and light commercial wiring.4.
Rigid PVC Conduit
Description
Rigid polyvinyl chloride (PVC) conduit. Connected using PVC cement.
Pros
Corrosion resistant. Lightweight. Relatively inexpensive. Easy to cut and assemble (no threading required).
Cons
Less physical protection than metal conduit. Requires a separate grounding conductor to be pulled through the conduit. Can become brittle in cold weather. Susceptible to damage from sunlight (UV degradation) if not painted or specifically UV-resistant. More prone to damage in hot weather
Typical Uses
Underground applications (direct burial or encased in concrete), corrosive environments (e.g., near saltwater).5.
Liquidtight Flexible Metal Conduit (LFMC) or Liquidtight Flexible Nonmetallic Conduit (LFNC)
Description
Flexible conduit with a liquidtight jacket. Connected using specialized fittings.
Pros
Flexibility allows for movement and vibration. Liquidtight seal protects conductors from moisture.
Cons
More expensive than EMT. Less physical protection than rigid conduit. Can be difficult to pull conductors through long runs.
Typical Uses
Short runs to connect equipment subject to vibration (e.g., generators, motors), connections in wet locations. Use sparingly – long runs of flexible conduit are generally discouraged.
Specific Recommendations for Your Installation (Based on Assumptions)
Without knowing your exact location or soil type, here's a general recommendation:1.
Underground Run to Generator
If you are running the conductors underground to the generator, use
Schedule 40 or Schedule 80 PVC conduit for direct burial. Remember to include a correctly sized green insulated grounding wire in the conduit with the other circuit conductors. Make sure to follow proper burial depth requirements (NEC table 300.5). For the stub-up coming out of the ground into the ATS and the generator, consider using RMC or IMC for added physical protection where it's exposed.2. Above Ground Between Meter, ATS, and Panel
IMC is often a good choice for above-ground runs between the meter, ATS, and panel. It provides a good balance of protection, cost, and ease of installation. Alternatively, RMC will offer even better protection and longevity. Use EMT is acceptable indoors or in protected locations, but less durable in exposed outdoor environments.3. Flexible Conduit
Use short lengths of
LFMC or LFNC (maximum 3-6 feet) for final connections to the generator and ATS, to allow for vibration and slight misalignment.4. Weatherproof Fittings
Use appropriate weatherproof fittings (e.g., raintight connectors, sealing locknuts) in all outdoor locations to prevent water from entering the conduit system.5.
Conductor Sizing
Ensure that the conductors you select are properly sized for the load of the generator and the ampacity of the breakers.6.
Grounding
Pay very close attention to grounding. A proper grounding system is crucial for safety and proper operation of the generator and ATS. Use grounding bushings and bonding jumpers as required. The generator should be properly grounded to the grounding electrode system of the house.7.
Support
Properly support all conduit runs with appropriate straps and hangers, spaced according to code.
Additional Tips for Professional Workmanship
Plan Your Route
Before starting, carefully plan the conduit route to minimize bends and obstructions. A well-planned route will result in a cleaner and more efficient installation.
Use a Conduit Bender
Learn how to use a conduit bender properly to create neat, consistent bends. Practice on scrap pieces first.
Ream Conduit
Always ream the ends of cut conduit to remove sharp edges, which can damage conductors.
Pulling Conductors
Use pulling lubricant to make it easier to pull conductors through the conduit. Don't overfill the conduit – follow the NEC fill requirements.
Labeling
Label all conduits and conductors clearly to identify their purpose. This will make future troubleshooting much easier.
Torque Fittings
Torque all fittings to the manufacturer's specifications. Overtightening or undertightening can compromise the connection.
Neat Wiring
Inside enclosures (ATS, panel), keep the wiring neat and organized. Use cable ties to bundle conductors together.
Important Considerations Specific to Generator Installations
Neutral Bonding
Understand the requirements for neutral bonding in generator installations. In some cases, the neutral may need to be switched by the ATS, depending on whether the service is separately derived. This is crucial for safety.
Load Calculation
Ensure the generator is adequately sized for the loads it will be powering. Perform a load calculation according to NEC Article 220.*
ATS Selection
Choose an ATS that is compatible with the generator and your electrical system. Consider features like load shedding and exercise timers.
Final Thoughts
There's no single "standard" way to pipe between the meter, ATS, and panel, but focusing on code compliance, using appropriate materials for the environment, and paying attention to detail will result in a safe and professional installation. Consult with your local electrical inspector if you have any questions. Good luck!
Disclaimer: I am an AI Chatbot and not a qualified electrician. This information is for general guidance only and should not be considered a substitute for professional advice. Always consult with a licensed electrician for all electrical work. Incorrect electrical work can be dangerous and can cause fire or electrocution. Flag for review