Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Starter Removal

User: Alwayslearningelec, Location: NJ

Asked on: Thursday, October 9, 2025 at 10:25 am EDT
Answered on: Thursday, October 9, 2025 at 10:25 am EDT

Question: Is this a difficult process to remove a starter in an MCC? These are 100A and 200A circuits.

Removing a starter in an MCC (Motor Control Center), even for 100A and 200A circuits, isn't inherently difficult in terms of mechanical skills. However, it's very high risk and requires a strict adherence to safety procedures and a good understanding of the MCC system. Here's a breakdown of why and what's involved

Why it's Potentially Dangerous:
High Voltage/Current

MCCs operate at potentially lethal voltages. Even after de-energizing the specific starter bucket, there can be residual voltage, capacitors, and live bus bars in close proximity. A mistake can lead to severe electrical shock or arc flash.


Complexity

MCCs are complex systems with interconnected components. Removing a starter without proper understanding can unintentionally affect other circuits or components.

Arc Flash Hazard

Disturbing connections, even when seemingly de-energized, can create an arc flash hazard, which is a powerful explosion of heat and light that can cause severe burns and even death.


Weight

Starters, especially for 200A circuits, can be heavy and awkward to handle.

Potential for Misidentification

Accurately identifying the correct starter in a crowded MCC lineup is crucial, and mistakes can be disastrous.

General Steps (assuming you are a qualified electrician following proper procedures - this is NOT a step-by-step guide, and assumes prior knowledge)



WARNING: These steps are for informational purposes ONLY. Do NOT attempt this work unless you are a qualified and experienced electrician familiar with MCC safety procedures and specific to the MCC being worked on.
1. Planning and Permitting



Job Hazard Analysis (JHA)

Conduct a thorough JHA to identify potential hazards and develop mitigation strategies.

Lockout/Tagout (LOTO)

Develop a detailed LOTO procedure. This is the MOST critical step.


Permits

Obtain any necessary permits required by your facility or local regulations.

Documentation

Review the MCC drawings, one-line diagrams, and any available maintenance records.


Spare Parts

Ensure you have the correct replacement starter and any necessary hardware.

Communication

Inform all relevant personnel of the work being performed and the potential impact.2.

De-Energizing and Lockout/Tagout



De-energize the MCC

This usually involves opening a main breaker or disconnect. Follow the LOTO procedure meticulously.

Verify Zero Energy

Use a properly rated voltage meter to verify that the starter bucket and associated wiring are completely de-energized. Test the meter before and after to ensure it's working correctly.


Lockout and Tagout

Apply lockout devices to the main disconnect and any other relevant breakers or disconnects. Affix tags warning against energization.3.

Physical Removal



Visual Inspection

Carefully inspect the starter and its connections for any signs of damage or overheating.


Disconnect Wiring

Carefully disconnect all wiring from the starter. Label each wire clearly to ensure proper reconnection. Use insulated tools.

Release Mounting Hardware

Loosen and remove the mounting bolts or screws that secure the starter in the bucket.


Remove the Starter

Carefully lift the starter out of the bucket. Get assistance if the starter is heavy.

Inspect the Bucket

Clean the bucket and inspect for any damage or debris.4.

Installation of New Starter



Install new starter carefully.
Reconnect all wiring carefully. Torque all connections to specification.5. Verification and Testing



Visual Inspection

Double-check all wiring connections and ensure that everything is properly installed.


Insulation Resistance Test (Megger Test)

Perform an insulation resistance test on the starter and its associated wiring to verify that there are no insulation faults.

Functional Test

After removing the LOTO devices, carefully energize the MCC and test the starter to ensure that it is functioning correctly.

Key Safety Considerations



Qualified Personnel

Only qualified electricians with specific training and experience in working on MCCs should perform this work.

Personal Protective Equipment (PPE)

Wear appropriate PPE, including arc-rated clothing, safety glasses, gloves, and hearing protection.


Arc Flash Study

Understand the arc flash hazard levels for the specific MCC and use appropriate PPE.

Rubber Matting

Use insulated rubber matting to reduce the risk of shock.


Buddy System

Work with a partner who can provide assistance in case of an emergency.

Communication

Maintain clear communication with all personnel involved in the work.


Follow Procedures

Adhere strictly to all safety procedures and best practices.

In summary, while the mechanical act of removing a starter isn't overly complex, the electrical safety considerations make it a very high-risk task that should only be performed by qualified personnel following strict safety procedures. Never underestimate the potential hazards of working on MCCs.
Consult with your company's safety department and a qualified electrical engineer for specific procedures and training related to your MCCs. Flag for review

Previous Question Next Question