Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 3 phase motor conductor tracing

User: ammklq143, Location: Iowa

Asked on: Thursday, October 9, 2025 at 3:29 pm EDT
Answered on: Thursday, October 9, 2025 at 3:30 pm EDT

Question: I have a customer who bought a used 3 phase motor and the motor conductors aren’t labeled, nor connected to anything. Some seem to be somewhat paired up with others but nothing clearly obvious or for certain.It’s a 12 wire motor and the high voltage is like the high voltage delta diagram in the bottom left corner of the link below.https://control.com/uploads/articles/Poster_3Phase_Motor_Wiring.png

Okay, dealing with unmarked 12-lead motors can be tricky, but with a systematic approach, you can figure it out. Here's a breakdown of how to identify and connect the windings for high-voltage delta operation, along with important safety precautions

Safety First!

1. Disconnect Everything

Before you even think about touching those wires, ensure the motor is completely disconnected from any power source. Lock out/tag out procedures are essential.2.

Verify No Voltage

Double-check with a reliable voltage meter that there's no residual voltage present.3.

Insulated Tools

Use insulated tools for all work.4.

Ground

Make sure the motor frame is properly grounded.5.

Qualified Personnel

If you're not 100% comfortable with this process,

hire a qualified electrician
. This is not a beginner project. Improper wiring can damage the motor, create a safety hazard, or both.

Understanding the 12-Lead High-Voltage Delta Configuration

The diagram you linked to illustrates the high-voltage delta connection. The key concept is that each phase of the three-phase power source is connected across two windings in series. This allows the motor to be connected to a higher voltage supply. The key is to understand which leads belong to which winding.

Identifying the Windings

This is the most critical and time-consuming part. You'll need an ohmmeter (multimeter set to measure resistance).1. Label Everything

Use numbered wire markers to label each of the 12 wires. This is absolutely essential to keep track of things. Label them 1 through 12.2.

Measure Resistance

Take resistance readings between every possible pair of wires (1 and 2, 1 and 3, 1 and 4... all the way to 11 and 12). Record every reading. A table or spreadsheet will be helpful.

Important

Look for pairs of wires that show a low and consistent resistance. This low resistance indicates that these two wires belong to the same winding. Typical resistance values for motor windings will be a few ohms or less, but this can vary based on motor size and construction. If a pair of wires are open (infinite resistance), they are not part of the same winding.3.

Pairing Strategy

Typically windings are paired together and close in proximity. Meaning, 1 may be paired with 2, 3 with 4 and so forth. However, this is not always the case. You may be paired to 12. The reason to test every wire to every other wire is to get an accurate assessment of each potential pairing.
4.


Document Your Findings

Create a table or list showing the wire pairs you've identified and their resistance values.5.

Confirmation and Troubleshooting
You should end up with 6 pairs. Each pair of leads will represent one end and the opposite end of a coil. If any of the resistances are zero or higher than expected, there's probably a short or open circuit in the winding. This is not something you can fix without specialized motor repair equipment and skills.

Connecting for High-Voltage Delta

Once you've identified the winding pairs, follow this diagram closely.1. Reference the Diagram

Refer to the bottom left delta diagram in the link you provided.2.

Wire Connections

Make the following connections based on your identified winding pairs (replace W1, W2, etc., with your actual wire numbers):

T1

Connect leads that are one side of the coil from leads (1 & 6)


T2

Connect leads that are one side of the coil from leads (2 & 4)

T3

Connect leads that are one side of the coil from leads (3 & 5)
Connect the other ends of the coils, pairs (7 & 12), (8 & 10), (9 & 11) together.3.

Double-Check

Before applying power, carefully double-check all connections against the diagram. Any mistake here could damage the motor.

Testing (Use Caution!)
1. No Load

Before connecting the motor to its intended load, test it with no load.2.

Voltage and Current Monitoring

Use a multimeter to monitor the voltage and current on each phase as you start the motor. The voltage should be close to your supply voltage, and the current should be relatively low (the motor's nameplate will give you an idea of the expected no-load current).3.

Listen and Observe

Listen for any unusual noises (humming, grinding, etc.) and watch for excessive vibration. If anything seems wrong, immediately disconnect the power and re-check your wiring.4.

Rotation

If the motor runs smoothly but in the wrong direction, swap any two of the three incoming power leads to reverse the rotation.

Important Considerations



Motor Nameplate

The motor nameplate is your best friend. It will tell you the voltage, amperage, horsepower, and other critical information.


Service Factor

Check the motor's service factor. This indicates how much overload the motor can handle safely.

Insulation Resistance

If you have a megohmmeter (megger), check the insulation resistance between the windings and the motor frame. Low insulation resistance indicates moisture or contamination in the windings, which can lead to failure.


Thermal Overloads

Always use correctly sized thermal overload protection for the motor to prevent damage from overcurrent. This is crucial for any motor installation.

Disclaimer:
Working with electrical equipment can be dangerous. I cannot provide electrical advice for your project as I don't know all of the parameters of the installation and don't have any control or understanding over your skill level. Always consult with a qualified electrician for any electrical work. Flag for review

Previous Question Next Question