Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Larger OCPD

User: redtruck, Location: Colorado

Asked on: Thursday, October 9, 2025 at 7:47 pm EDT
Answered on: Thursday, October 9, 2025 at 7:47 pm EDT

Question: Hello,I am wondering if, where applicable you can install larger wiring and OCPDs than 125% of inverter or total PV system output.I have multiple situations for why#1 - Standard or available meter collars for a supply-side interconnection only come in 60 or 80a configurations. Say the output of my system is 55ampsx1.25=68.75 or 70a breaker. The meter collar's 80a is too large, no problem, I still run #4CU THHN, I do not want to buy a 100a fused disconnect to fuse down to the "appropriate" total system OCPD of 70A.#2 I may install a system with plans to expand in the future, I can just install larger wiring and breaker right now thus making the total process of adding future strings or upgrading an inverter simpler in the future.690.9(B) states OCPD are permitted to be rounded up to the next standard size. Is this inferring it cannot be sized up larger than one standard size?I understand it is easy to simply install the correct wiring, I am just curious if you guys have done this. Normally when wiring up a load such as a motor, I do not want my OCPD to be needlessly large - I am trying to protect the wiring AND the motor itself. This however is power production, an inverter will not just overdraw current, will it?Is my thinking flawed? Thanks

Okay, let's break down your questions regarding oversizing wiring and OCPDs in PV systems, especially in the context of supply-side interconnections and future expansion.

General Principles



Overcurrent Protection (OCP)

The primary purpose of an OCPD (circuit breaker or fuse) is to protect conductors from overcurrent that could damage or overheat them, potentially causing a fire. Secondary protection is for the equipment it feeds.


Conductor Ampacity

Conductors must be sized appropriately for the maximum current they are expected to carry, taking into account ampacity derating for temperature and conduit fill.

NEC Compliance

All PV system installations
must comply with the National Electrical Code (NEC), specifically Article 690 for solar photovoltaic (PV) systems. Also, any local AHJ's rules.

Engineering Judgement

While the NEC provides a framework, sound engineering judgment is crucial, especially when deviating from typical practices.

Addressing Your Specific Scenarios



#1 - Meter Collar Limitations and OCPD Size



The Problem

You have a calculated OCPD requirement of 68.75A (based on 125% of inverter output), but your available meter collar only comes in 60A or 80A options.


NEC and Practical Considerations



690.9(B) Rounding Up

690.9(B)
does allow rounding up the OCPD to the next standard size if the calculated value doesn't match a standard breaker size. However, the code is silent as to whether you can round to a size 2 steps larger than calculated. It implicitly suggests that the rounding should be to the nearest standard size.

Potential Violations

Using an 80A breaker may be a violation, depending on the specific interpretation of the AHJ. This is because you're going significantly above the calculated 125% requirement, potentially compromising the circuit's ability to trip on overcurrent situations below 80A. The NEC requires the OCPD to trip before the conductor is damaged. This is especially true when dealing with the sensitive electronic components of PV inverters that cost thousands of dollars to replace.

Conductor Sizing

If you
do decide to use an 80A OCPD (with approval from the AHJ), you MUST ensure your conductors are rated for at least 80A after all derating factors are applied. #4 Copper THHN is usually good, but you need to verify based on your specific installation conditions.

Alternatives (Recommended)



Fused Disconnect

The best and safest practice is to use a fused disconnect. Yes, it adds cost and space, but it provides the
correct level of overcurrent protection for your conductors and inverter. In your case, use a 100A fused disconnect with 70A fuses (or whatever standard size is closest to your calculation). This gives you the required protection and a readily available disconnect. This will cost more and you specified you want to avoid this; I believe for good reason to use the correct OCPD

Contact the AHJ

Discuss the situation with your local electrical inspector or AHJ. They may have specific requirements or interpretations that clarify whether using the 80A meter collar is acceptable in their jurisdiction. Get their decision in writing if possible. If they say it is okay that does not mean its the safest option, it just means they may let it slide. The inspector may have some leeway to allow it, but it may not be in the best interest of the owner.

Find a Smaller Meter Collar

Exhaust all options for finding a meter collar closer to your calculated OCPD requirement. They do exist; it might just take some searching.

#2 - Future System Expansion



The Idea

Install larger wiring and OCPDs now to simplify future expansions.

NEC and Practical Considerations



Oversizing Conductors

Oversizing conductors for future expansion is generally acceptable and often recommended. Just make sure the existing OCPD protects the existing components, not the potential future components. The NEC generally allows you to install conductors with higher ampacity than required for the current load (as long as the OCPD is appropriately sized for the load the conductors are currently serving).

Oversizing OCPDs (Problematic)

Oversizing OCPDs
solely for future expansion is not generally allowed or advisable. As mentioned earlier, the OCPD's primary function is to protect the conductors and existing equipment. An oversized OCPD can lead to damage if a fault occurs. The code requires the OCPD to trip before the conductor is damaged.

Plan for Expansion

The better approach is to plan for expansion. That means:

Conduit Size

Use a conduit size that can accommodate the
future conductors you anticipate needing.

Subpanel

Install a larger subpanel than you currently need, with space for future breakers.

Documentation

Keep detailed records of your installation, including conductor sizes, conduit sizes, and OCPD ratings. This will make future expansion much easier.


How to Expand Safely

When you expand, you can then replace the existing OCPD with one appropriate for the new, larger system, making sure to upgrade the conductors as needed.

Inverter Behavior and Overcurrents



Inverters and Overcurrents

You're right that inverters don't typically "overdraw" current like a motor might. However, inverters
can experience internal faults or failures that could result in excessive current flow. This is especially true if the inverter is subjected to overvoltage, lightning strikes, or other electrical disturbances.

GFDI Protection

Inverters also have ground fault detection interrupters (GFDIs). They are designed to trip an internal breaker in the event of a short circuit or other failure in the equipment. This is a function that protects the equipment. If this trips, the external overcurrent protection should trip as well.

Your Thinking - Flawed?


Your thinking is partially flawed. You're correct that you don't want an OCPD to be needlessly large for a motor because it won't protect the motor from overload conditions. However, with PV systems, the primary goal of the OCPD is to protect the conductors from overcurrent caused by faults (internal inverter failure, ground faults, etc.). Oversizing conductors for future expansion is a reasonable approach. Oversizing OCPDs beyond what's necessary to protect the current conductors and equipment is generally not recommended and may violate the NEC.

Recommendations


Prioritize Safety

Always prioritize safety and compliance with the NEC.2.

Correct OCPD Sizing

Use the correct OCPD size for the conductors and equipment you are currently installing. If you need to round up, do so only to the nearest standard size if allowed by the AHJ.3.

Plan for Expansion

Plan for future expansion by oversizing conduits and using a larger subpanel.4.

Fused Disconnects

Use fused disconnects where necessary to provide proper overcurrent protection, especially for supply-side interconnections.5.

Consult the AHJ

Always consult with your local electrical inspector or AHJ to clarify any questions and ensure your installation meets their specific requirements.6.

Documentation:
Maintain detailed documentation of your installation for future reference.By following these guidelines, you can ensure a safe, reliable, and expandable PV system. Flag for review

Previous Question Next Question