Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Lighting & Recep Load Calcs on Multiple Panels

User: hitehm, Location: Las Vegas NV

Asked on: Friday, October 10, 2025 at 6:03 pm EDT
Answered on: Friday, October 10, 2025 at 6:03 pm EDT

Question: Situation: Customer has a (very common in our area) 400A square-D service panel in the attached garage that splits between 2 service disconnects, one 200A mb supplying the local bus and one 200A mb feeding a remote subpanel in the laundry room. The local bus has NO lighting circuits but does have general-purpose receptacle circuits. All the lighting circuits are in the remote subpanel. The back-fed solar breaker lands on the local bus. Inspector wants load calcs done on each panel.So, the question is for the local panel, how do we separate out the general-purpose receptacle circuits from the lighting circuits for the load calcs if they are both tied to the sq footage? And if not separated, how is it done? It seems overkill and inaccurate to apply the full 3va/sf for a panel with no lighting loads just for the receptacles. BTW, the remote panel has both lighting and receptacle circuits so applying the full 3va/sf seems reasonable in my opinion.

This is a common situation and a reasonable concern. Here's how to approach the load calculation issue with the inspector, emphasizing code compliance and real-world usage

Understanding the Code (NEC) and its Intent

The core of your discussion with the inspector should revolve around the intent of NEC Article 220, particularly Article 220.12, 220.14(I), and 220.
11. The purpose of the code is to ensure there's sufficient capacity to handle reasonably expected loads.

Here's a breakdown of how to handle the local panel load calculation


Communicate with the Inspector

Start by clearly explaining the situation to the inspector: "This panel [local] specifically has no lighting circuits. All lighting is fed from the remote subpanel." "Applying the full 3 VA/sq ft to this panel, which solely serves receptacles, overestimates the actual load significantly." "We want to arrive at a load calculation that is both code-compliant and reflects a reasonable real-world scenario."2.

Propose an Alternative Calculation Method (with Code Justification)

You have a few options, and you should choose the one that provides the best balance between accuracy and code compliance. Each approach requires a discussion with your inspector
before you implement it!

Option A: Modified General Lighting Load
Argument

While technically "general lighting," the receptacle circuits
are used for some lighting (lamps, holiday lighting, etc.). However, they are also used for appliances, tools, and other general purposes.

Calculation

Calculate the total square footage of the dwelling (or the area this local panel serves, if well-defined). Reduce the VA/sq ft calculation for the local panel, justified because this panel only feeds receptacles. A reasonable reduction could be to use 1 VA/sq ft for the receptacles fed by the local panel. Clearly document your rationale on the load calculation sheet.

Code Reference

While there's no specific exception for this scenario, you can argue that this approach still provides an adequate safety factor and avoids over-inflating the load. Section 220.12 allows for the use of more specific load calculations based on the actual use of the area in question.

Option B: Minimum Receptacle Outlets Load Only
Argument

This approach calculates a minimum load for the receptacles, without including the general lighting.

Calculation

Count the number of receptacle outlets on circuits fed by the local panel. This includes wall receptacles, floor receptacles, and countertop receptacles. Multiply the number of outlets by 180 VA per outlet. (NEC 220.14(I)). This accounts for the minimum load per receptacle.

Pros

This approach is straightforward and clearly grounded in the NEC.

Cons

It might still be seen as an overestimate if you can demonstrate that the receptacle usage is likely to be lower than the minimum.


Code Reference

NEC 220.14(I)

Receptacle Outlets. Except as permitted elsewhere in this section, each receptacle outlet shall be calculated at not less than 180 volt-amperes.
Option C: Specific Appliance Load (Most Accurate, Most Work) Argument

If you know, with reasonable certainty, the appliances and devices that will be plugged into the receptacles fed by the local panel, you can calculate their specific loads.


Calculation

List each appliance and device expected to be used. Calculate the VA of each appliance (Volts x Amps). Apply demand factors as appropriate (NEC 220.40 - 220.61).

Pros

Most accurate representation of the actual load.

Cons

Requires significant effort to identify and calculate the loads. Difficult to account for unknown future loads.


Code Reference

NEC 220.10 and subsequent sections on specific load calculations.
3.


Highlighting the Reality of Usage

Emphasize that it's unlikely that all the receptacles on the local panel will be used at their maximum capacity simultaneously. Demand factors are intended to account for this. Consider pointing out the solar panel contribution. The solar panel will offset some of the load on the service, especially during daylight hours.4.

Document Everything

Clearly document the calculations you used, including the square footage of the dwelling, the VA/sq ft figure used, the number of receptacle outlets, and any assumptions made. Keep a record of your discussions with the inspector, including the date, time, and topics discussed.

Key Talking Points with the Inspector



Safety

Assure the inspector that the proposed alternative calculation will still result in a safe and adequate electrical system.


Accuracy

Emphasize that the alternative calculation provides a more accurate representation of the actual load than simply applying the full 3 VA/sq ft.

Flexibility

While the code provides a general framework, it also allows for flexibility in specific situations, especially when it can be demonstrated that the standard calculation is inappropriate.

Important Considerations



Local Amendments

Be aware of any local amendments to the NEC that might affect the load calculation requirements.

Inspector Authority

Ultimately, the inspector has the final say. Be respectful of their authority and be prepared to compromise if necessary.


Professionalism

Present your case in a professional and respectful manner. A collaborative approach is more likely to yield a positive outcome.

Example of Documentation

"Load calculation for 400A service panel with two 200A main breakers. The local 200A panel supplies general-purpose receptacles only. The remote 200A panel supplies lighting and additional receptacles.

Local Panel Load Calculation (General Purpose Receptacles Only):
Total Dwelling Square Footage: 2000 sq ft Adjusted General Lighting Load (Receptacles Only): 1 VA/sq ft (Justification: This panel exclusively serves receptacles and not lighting fixtures) Adjusted General Lighting Load: 2000 sq ft x 1 VA/sq ft = 2000 VA* Other Loads: (List any other loads connected to the local panel)This approach acknowledges the general lighting requirement but applies a reasonable adjustment to account for the absence of lighting fixtures on this specific panel. "By approaching the inspector with a well-reasoned argument, code references, and a proposed alternative calculation, you increase the chances of reaching a mutually agreeable solution that ensures a safe and compliant electrical installation. Good luck! Flag for review

Previous Question Next Question