Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Has anyone configured a BMS 8–20S module with CAN and 485 communication at the same time?

User: jayden, Location: Philippines

Asked on: Sunday, October 12, 2025 at 6:30 am EDT
Answered on: Sunday, October 12, 2025 at 6:30 am EDT

Question: I’m testing a new pack setup using an 8S LiFePO4 configuration and trying to enable both CAN and RS-485 for data logging and inverter communication. The module responds fine on 485, but CAN seems inactive even though it’s properly wired. Do I need to toggle protocol priority in firmware, or is it limited to one active communication channel at a time?

You're on the right track thinking about protocol priority. Here's a breakdown of the likely causes and how to troubleshoot them

1. Firmware Configuration: The Most Likely Culprit
Protocol Selection

Many battery management systems (BMSs) and similar modules require you to explicitly select the active communication protocol(s) through firmware settings. It's
highly likely your issue stems from this. You may need to:

Find the Setting

Look for configuration options in the BMS software related to "Communication Protocol," "CAN Bus Enable," "RS-485 Enable," "Protocol Priority," or similar terms.

Enable Both

Ensure
both CAN and RS-485 are enabled. Sometimes there's a master enable/disable, and then individual enables for each protocol.

Protocol Priority (If Present)

Some devices allow you to set a priority. If both are enabled but CAN still doesn't work, experiment with different priorities. It's unusual, but some systems might default to RS-485 if it's a higher priority. However, generally, enabling both is what matters most.

Baud Rate and Node ID

CAN bus
absolutely requires matching baud rates and unique node IDs for all devices on the bus.

CAN Baud Rate

The most common baud rates for CAN in battery systems are 250kbps and 500kbps. Verify your BMS and your CAN interface (e.g., CAN analyzer, inverter) are set to the exact same baud rate. A mismatch will prevent communication. Use a CAN analyzer to sniff traffic and confirm it's using the expected rate.

CAN Node ID

Each device on the CAN bus
must have a unique node ID (also called a CAN ID or device ID). Check the BMS's settings and ensure it has a valid ID (often 1-127) and that it doesn't conflict with other devices on your CAN bus. Duplicates will cause bus errors and prevent communication.

Termination Resistors

CAN bus requires a 120-ohm termination resistor at each end of the bus. If you're only testing with the BMS and a CAN interface, then the resistor needs to be placed physically at each of those end points. Missing or incorrect termination is a very common cause of CAN issues.

2. Wiring Issues (Double-Check)
CAN High and CAN Low

Make absolutely sure CAN High is connected to CAN High and CAN Low is connected to CAN Low. Reversing them is a common mistake.


Shielding

If your CAN cable has shielding, properly ground it at one end only (preferably the end connected to the device with the lowest ground potential). Avoid creating ground loops.

Wire Gauge and Length

For longer CAN bus runs, use appropriate gauge wire to minimize voltage drop. Keep the overall bus length within the CAN bus specification limits for your chosen baud rate.


Connectors

Ensure your CAN connectors are making good contact. Loose or corroded connections can cause intermittent or complete communication failures.

3. Hardware Problems
Faulty CAN Transceiver

It's possible the CAN transceiver in the BMS is faulty. If you have another device with a CAN interface, you could try swapping it in to see if the problem persists.


Driver Issues (For PC-Based CAN Interfaces)

If you're using a USB-CAN adapter or similar, make sure you have the correct drivers installed on your computer.

CAN Analyzer Configuration

If you are using a CAN analyzer, make sure that its interface is correctly configured.

4. Limited Concurrent Communication (Less Likely, But Possible)
Simultaneous Operation Restrictions

While less common, some BMSs might be designed to operate either CAN or RS-485 at a time, but not both simultaneously due to hardware limitations or software constraints. This is something you'd need to consult the BMS documentation or contact the manufacturer to confirm.

Troubleshooting Steps


Review the BMS Documentation

The most important thing is to consult the BMS manual. It should detail the CAN configuration, including baud rate, node ID settings, termination requirements, and any limitations on simultaneous protocol usage.2.

Double-Check Wiring (Again)

Verify all connections, polarity, and termination resistors.3.

Check Baud Rate and Node ID

Use the BMS configuration software (if available) or a CAN analyzer to verify the BMS is configured with the correct baud rate and a unique node ID.4.

CAN Analyzer/Sniffer

Use a CAN analyzer to "listen" on the CAN bus. This will tell you: If the BMS is transmitting anything at all. The CAN ID being used by the BMS. The CAN baud rate. If there are any bus errors (e.g., arbitration lost, CRC errors).5.

Simplify

Disconnect all other devices from the CAN bus except the BMS and your CAN interface. This eliminates the possibility of node ID conflicts or other devices interfering.6.

Factory Reset

If possible, try a factory reset of the BMS. This can clear any corrupted settings that might be causing the issue.7.

Contact Manufacturer Support

If you've exhausted all other options, reach out to the BMS manufacturer's technical support. They may have specific troubleshooting steps or be aware of known issues.

Example Scenarios and Solutions



Scenario

CAN bus is silent, and your CAN analyzer shows nothing.


Likely Cause

CAN disabled in firmware, incorrect baud rate, incorrect wiring (CAN High/Low reversed), missing termination resistors, or a faulty CAN transceiver.

Solution

Check firmware settings, verify wiring, add termination resistors, try a different CAN transceiver.


Scenario

CAN analyzer shows messages from the BMS, but your inverter isn't responding.

Likely Cause

Inverter not configured to listen to the BMS's CAN ID, inverter baud rate mismatch, or incompatibility between the BMS and inverter's CAN protocols.


Solution

Check inverter configuration, verify baud rate, consult inverter documentation about supported CAN protocols (e.g., CANopen, J1939).

Scenario

CAN analyzer shows error frames on the bus.


Likely Cause

Node ID conflict, incorrect termination resistors, or noise on the bus.*

Solution:
Ensure all devices have unique node IDs, check termination resistors, use shielded cable, and ground the shield properly.By systematically checking these possibilities, you should be able to isolate the cause of your CAN communication problem and get your 8S LiFePO4 pack working as intended. Remember to consult the documentation for both the BMS and any other devices on the CAN bus. Flag for review

Previous Question Next Question