Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 277v and 120v device without barrier.

User: darekelec, Location: nyc

Asked on: Monday, October 13, 2025 at 9:47 am EDT
Answered on: Monday, October 13, 2025 at 9:52 am EDT

Question: Will I get 380V difference in potential between devices every time or is there a phase combination that barrier will not be necessary?Meaning if I choose corresponding windings of a transformer the voltage will be less than 150V between devices and no barrier is required.Thank you.

Let's break this down to understand the potential for 380V and how to achieve lower voltages.

Understanding 380V in a Three-Phase System 380V is typically a line-to-line voltage. In a standard European three-phase system, the voltage between any two of the three phases is 380V (or sometimes 400V, depending on the specific system and tolerances). Line-to-neutral voltage is lower. The voltage between any one phase and the neutral wire is typically around 220V (or 230V).

Why 380V Potential Differences Exist

If you are connecting different devices to different phases in a three-phase system without careful planning, you will see that 380V difference in potential. Each device will have its ground/chassis tied to the local neutral of the system (or Earth ground). Because the phases are 120 degrees apart, the voltage between any two phases is significant.

Achieving Lower Voltages and Avoiding Barriers

Yes, you can absolutely arrange your connections to avoid a 380V potential difference between devices and potentially eliminate the need for a barrier (depending on the specific safety regulations you need to follow). Here's how:1. Use the Same Phase and Neutral

Connect both devices to the same phase and neutral of your three-phase system. If both devices are powered by the same 220V (or 230V) phase, the potential difference between them will be minimal (ideally, zero, but practically, a few volts due to voltage drop in the wiring).2.

Use a Step-Down Transformer (Single-Phase or Three-Phase)



Single-Phase

If you only need single-phase power, a single-phase step-down transformer can convert your 380V (line-to-line) to a lower voltage like 120V or 24V. You would then connect both devices to the output of this transformer.


Three-Phase

A three-phase step-down transformer can provide multiple lower voltage outputs, potentially allowing you to power multiple devices with a reduced voltage difference.3.

Isolation Transformer

An isolation transformer provides galvanic isolation, meaning there's no direct electrical connection between the input and output. This prevents any ground loops or potential differences between devices connected to the output. You can find isolation transformers with various voltage ratios.4.

Consider the "Neutral" or Grounding

Ensure proper grounding. Make sure the neutral of your power supply (or the secondary of a transformer) is properly grounded according to your local electrical codes. Improper grounding can lead to unexpected voltage differences. Avoid ground loops. If devices are connected to different ground points that have a small voltage difference, it can cause current to flow through the grounding conductors, potentially causing problems.

Important Considerations



Safety Regulations

Local electrical codes and safety regulations are paramount. The 150V barrier requirement you mentioned is likely related to a specific safety standard.
Always consult with a qualified electrician to ensure your wiring and setup comply with all applicable regulations.

Isolation

Barriers aren't always about voltage alone. They can also be required for isolation to prevent accidental contact with hazardous voltages.

Device Specifications

Check the input voltage requirements of each device. If one device is designed for 220V and another for 120V, you'll need a transformer or separate power supplies anyway.


Power Consumption

Ensure the transformer you choose can handle the combined power requirements of all connected devices.

Example

Let's say you have two devices that need to be close together and you want to avoid a 380V potential difference.1.

Solution

Use a single-phase step-down transformer to convert your 380V (line-to-line) to 120V.2.

Wiring

Connect the 380V input of the transformer to two of the three phases of your three-phase supply. Connect both devices to the 120V output of the transformer. Ensure the neutral of the 120V side of the transformer is properly grounded.

In summary:
You don't have to have a 380V potential difference between devices. By carefully planning your connections and potentially using transformers, you can significantly reduce the voltage difference and possibly eliminate the need for barriers, while always adhering to safety regulations.* Consult with a qualified electrician! Flag for review

Previous Question Next Question