Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Engineers always detail duct bank with encased concrete. What should I detail instead?

User: LifeLongLearner, Location: Rhode Island

Asked on: Tuesday, October 14, 2025 at 3:59 pm EDT
Answered on: Tuesday, October 14, 2025 at 4:00 pm EDT

Question: The firms I've been at always detail a duct bank with encased concrete for the service no matter the situation. The system I'm working on is 480V and has a 600A secondary service for an office building, and a 600A service for a PV system over the parking lot. I'm thinking of detailing (2) 3" Sch. 40 PVC to be buried with back fill (no concrete). Depths will be detailed per Table 300.5(A). The runs are ~100'. When would fiberglass conduit come into play?

You're asking a great question about cost-effective and appropriate conduit selection for your application. Let's break down the considerations for PVC, encased concrete, and fiberglass, particularly in the context of your 480V, 600A services.

Why the Default to Encased Concrete? (and why it might not always be needed)

Firms often default to concrete encasement for several reasons, even if it's overkill: Perceived Protection

Concrete offers robust physical protection against digging, soil shifting, and even some chemical exposure. It's seen as a "bulletproof" solution.


Consistency

It can be easier to have a standardized detail for all underground services. It simplifies design and installation training.

Risk Aversion

Avoiding potential problems (and related liability) is a powerful motivator. The "better safe than sorry" approach often prevails.


Heat Dissipation (Sometimes Misunderstood)

While concrete can improve heat dissipation in some very specific, high-load scenarios, it's often not a significant factor for typical service entrances. For smaller conduit runs, the concrete's thermal properties don't usually make a huge difference.

Local Code or Utility Requirements

Some jurisdictions or utilities mandate concrete encasement for certain voltage levels or service sizes regardless of other factors.
Always check local requirements first.

Your Situation: Is Concrete Encasement Necessary?


Given your 480V, 600A services and the use of (2) 3" conduits per service, concrete encasement
may be unnecessary. Here's a breakdown: Code Requirements (NEC)

The NEC allows for direct burial of Schedule 40 PVC, provided you meet the depth requirements outlined in Table 300.5(A). For 480V, you'll likely need a minimum of 18" of cover.

Soil Conditions

Consider the soil type. Stable, well-compacted soil is better suited for direct burial. If the soil is rocky or prone to shifting, some additional protection might be warranted (but not necessarily full concrete encasement).


Loading/Heat Dissipation

With two 3" conduits per service, you have ample capacity and space for heat dissipation. A 600A service isn't an extreme load in this context, especially with the use of parallel conduits.

Mechanical Protection

Consider vehicle traffic above the burial area. If there's a risk of heavy vehicles directly impacting the buried conduits, you may want more protection.


Markers

Regardless of whether you use concrete or not, be sure to install detectable warning tape above the conduits as per code.

Why Your Approach (Direct Burial PVC) Is Likely Suitable



Cost Savings

Ditching the concrete significantly reduces material and labor costs.


Easier Installation

Direct burial is faster and less labor-intensive.

Sufficient Protection

Schedule 40 PVC, when properly installed at the correct depth with warning tape, provides adequate protection against most common hazards.


Appropriate for the Load

As mentioned earlier, 600A at 480V, split into two conduits per service, isn't a particularly demanding thermal load.

When Does Fiberglass (RTRC) Conduit Come Into Play?


Fiberglass conduit (RTRC - Reinforced Thermosetting Resin Conduit) offers some distinct advantages over PVC and encased concrete, making it suitable in specific scenarios: Extreme Corrosion Resistance

RTRC excels in environments with high levels of corrosive chemicals (e.g., industrial plants, wastewater treatment facilities, areas with high salt content). It's often used where PVC would degrade rapidly.


High Strength-to-Weight Ratio

RTRC is stronger than PVC for the same weight. This can be important in long runs or in areas where weight is a concern.

Lower Thermal Expansion

RTRC has a lower coefficient of thermal expansion than PVC. This means it expands and contracts less with temperature changes, reducing stress on joints and supports, especially in long, exposed runs. This isn't as much of a factor in buried applications because the temperature remains relatively constant.


Non-Conductive

Fiberglass is a naturally non-conductive material, making it inherently safer in some situations.

Direct Burial Without Concrete

RTRC can be direct buried and does not require concrete encasement in most situations, offering a good balance of protection and cost-effectiveness when PVC is deemed insufficient.


Duct Bank Replacement/Rehabilitation

RTRC is sometimes used to reline existing duct banks, offering a cost-effective alternative to complete replacement.

In Your Specific Case, Fiberglass is Probably Not Necessary Unless

The soil is highly corrosive. There are specific local codes or utility requirements mandating it. You need significantly more mechanical protection than Schedule 40 PVC can provide, but don't want the expense of concrete encasement.

Recommendation


Verify Local Requirements

This is the most important step. Check with the local electrical inspector and the utility company for their specific requirements for underground service entrances. Their rules supersede general NEC guidelines.2.

Soil Analysis

A soil test can determine corrosivity.3.

Risk Assessment

Assess the likelihood of physical damage from digging or heavy vehicles.4.

Cost Comparison

Get quotes for PVC, RTRC, and concrete encasement to see the actual cost differences in your area.5.

Document Your Decision:
Clearly document your rationale for choosing direct burial PVC in your design documents. Include the NEC references, soil conditions, and any relevant code interpretations. This helps justify your design choices if questions arise later.In summary, it sounds like your proposal for direct burial Schedule 40 PVC is likely appropriate and cost-effective, assuming* it meets all local code and utility requirements. Don't be afraid to challenge the default practice of concrete encasement, especially if it's not truly necessary. Just be sure to do your due diligence and document your decisions. Flag for review

Previous Question Next Question