Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Disconnecting means

User: eds

Asked on: Wednesday, October 15, 2025 at 9:17 am EDT
Answered on: Wednesday, October 15, 2025 at 9:17 am EDT

Question: I am doing a residence that might have a solar field and tesla powerwall 3. Remote meter pedestal, with my 200 amp panel mounted in the basement nearest the point of entry. I think I need to disconnect the dc conductors before they enter the house, will I also need to install a disconnect outside the the ac panel?

Okay, let's break down the disconnect requirements for your residential solar and Tesla Powerwall 3 setup, focusing on code compliance (primarily NEC - National Electrical Code) and best practices.

Understanding the Components Solar Field

This generates DC electricity.


Tesla Powerwall 3

This is a battery energy storage system (BESS) that stores DC electricity and inverts it to AC for use in your home. It also has an integrated solar inverter.

Remote Meter Pedestal

This is where the utility meter is located, typically outside the house. It's the point where the utility grid connects to your electrical system.


200A Panel in Basement

This is your main service panel, distributing power throughout your house.

DC Disconnect Requirements (Between Solar and Inverter/Powerwall)
Yes, you most likely need a DC disconnect. NEC 690.13(B) typically requires readily accessible disconnects for all ungrounded conductors from the solar array. This disconnect needs to be rated for the voltage and current of the PV system. Location of DC Disconnect

Ideally, the DC disconnect should be located outside the building, or as close as possible to the point where the DC conductors enter the building. This allows emergency responders to quickly shut down the solar system. Since the Powerwall 3 has an integrated inverter, you'll be disconnecting the DC before it enters the Powerwall. If the DC conductors run inside the building for a significant distance (e.g., a long run from the roof to the basement), an additional DC disconnect might be required closer to the array. This is to limit the amount of DC wiring within the building in case of a fault.

Purpose

The DC disconnect isolates the solar array from the rest of the electrical system, allowing for safe maintenance, troubleshooting, and emergency shutdown.

AC Disconnect Requirements (Between Powerwall and Main Panel)
Yes, you almost certainly need an AC disconnect. NEC 705.22 and 706.15 requires a readily accessible AC disconnect for the output of the inverter, typically located near the main service panel or on the exterior of the building. Location of AC Disconnect



Inside at the Main Panel

The AC disconnect must be readily accessible and located at the point where the Powerwall's AC output connects to your main panel. This allows you to isolate the Powerwall from the rest of your electrical system.

Outside

It is highly recommended to also have an AC disconnect located
outside the house, near the meter pedestal (if possible) or in another readily accessible outdoor location. This is critical for emergency responders. It allows them to completely de-energize your entire electrical system, including the solar and battery components, without having to enter the building.

Purpose

The AC disconnect isolates the Powerwall's AC output from the main panel, allowing for safe maintenance, troubleshooting, and emergency shutdown. It also serves to prevent backfeeding the grid during a power outage if the Powerwall is not properly configured for islanding.

Important Considerations & Summary
1. Local Codes and AHJ (Authority Having Jurisdiction)

The NEC is a minimum standard. Your local codes or the requirements of your AHJ (e.g., the city or county electrical inspector) may be stricter.

Always consult with your local building department and electrical inspector before starting any work.
They have the final say on what is required in your area.2. Rapid Shutdown Systems (RSD)

The NEC requires rapid shutdown of PV systems to reduce the shock hazard to firefighters. The Powerwall 3 may have rapid shutdown capabilities built in, but you need to ensure it meets the requirements of NEC 690.12. This often involves installing additional RSD devices at the array itself.
3.


Overcurrent Protection

Each circuit (DC and AC) must have appropriate overcurrent protection (fuses or circuit breakers) to protect the wiring and equipment from damage due to short circuits or overloads.4.

Signage

The NEC requires specific signage to be placed at the disconnects and other points in the system to warn of the presence of DC voltage and battery systems.5.

Professional Installation is Highly Recommended

Solar and battery systems involve complex electrical installations with potentially dangerous voltages and currents. It's strongly recommended that you hire a qualified and licensed solar installer to design and install the system. This will ensure that the system is installed safely and in compliance with all applicable codes.

In summary, here's a checklist



DC Disconnect

Required outside, near the point of entry of DC conductors. Consider an additional disconnect near the solar array if the DC wiring run inside the building is long.


AC Disconnect

Required inside at the main panel. Highly recommended outside, near the meter or in a readily accessible location.

Rapid Shutdown System (RSD)

Likely required to comply with NEC 690.12.


Overcurrent Protection

Fuses or breakers for all DC and AC circuits.

Signage

Clearly label all disconnects and other components.


Permits and Inspections

Obtain all necessary permits and inspections from your local building department.*

Professional Installation:
Strongly recommended.By following these guidelines and consulting with qualified professionals, you can ensure that your solar and battery system is installed safely and in compliance with all applicable codes. Good luck with your project! Flag for review

Previous Question Next Question