Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 22/2 + 18/2 Automation/Control Cable question

User: JJWalecka, Location: New England

Asked on: Wednesday, October 15, 2025 at 2:49 pm EDT
Answered on: Wednesday, October 15, 2025 at 2:49 pm EDT

Question: Would a shielded 4 wire work in place of 22/2 + 18/2 Automation/Control Cable?

Yes, a shielded 4-wire cable could work in place of a 22/2 + 18/2 automation/control cable, but it's crucial to verify compatibility and safety. Here's a breakdown of what you need to consider

Understanding the Cables:
22/2 + 18/2 Automation/Control Cable

This means you have two pairs of wires. One pair is 22 gauge (AWG) and the other is 18 gauge (AWG). Typically, the 22 AWG wires would be for low-current signals or communication, and the 18 AWG wires would be for power.


Shielded 4-Wire Cable

This is a cable with four wires, all within a conductive shield. The shield helps protect the signals from electromagnetic interference (EMI).

Key Considerations for Compatibility


Wire Gauge (AWG) and Current Capacity



Critical

The gauge of the wires in your shielded 4-wire cable

must
be equal to or larger than the gauge of the wires in the original cable. If you have 22/2 + 18/2, your shielded cable must have at least two 18 AWG wires and two 22 AWG wires (or larger - smaller AWG number indicates a larger wire). Do not use a thinner gauge wire for power! This can lead to overheating and fire hazards. Example

If your shielded cable has four 20 AWG wires, it could replace the 18 AWG wires, but you need to confirm it can handle the required current. Using 20 AWG instead of 22 AWG would be fine.

How to check Current Capacity

Look up the current carrying capacity (ampacity) of each wire gauge. Ensure the chosen gauge can handle the maximum current expected on that wire. Consult electrical codes for your region, as ampacity varies with installation methods (e.g., bundled in conduit vs. free air).2.

Voltage Rating



Important

The voltage rating of the shielded cable must be equal to or greater than the voltage used in the application. This is usually marked on the cable jacket.3.

Signal Type



Consider

Determine what signals are being carried by each pair of wires in the original cable (e.g., power, data, analog signals). Ensure your replacement cable is suitable for those signal types. The shielded cable should be good for all standard signals but make sure to verify.4.

Shielding Requirements



Benefit

The shielded cable adds protection against EMI (electromagnetic interference). If the original cable was in a noisy electrical environment, the shielded cable is a definite upgrade. If the original application did not require shielding, adding it generally won't hurt.5.

Cable Flexibility and Environment



Physical Characteristics

Make sure the shielded cable is flexible enough for the application and rated for the environmental conditions (temperature, moisture, sunlight, chemicals) it will be exposed to.6.

Wiring Configuration



Adaptation

Decide how you'll use the four wires in the shielded cable. You'll need to map each wire to the correct function. Document this clearly!7.

Grounding the Shield



Crucial

The shield
must be properly grounded to be effective. Typically, you ground it at one end only (usually the source end) to prevent ground loops. Consult best practices for shield grounding in your application.

Example Scenario

Let's say you're replacing a cable that controls a low-voltage DC motor.
The 18/2 wires carry power (e.g., 24V DC) to the motor. The 22/2 wires carry a control signal (e.g., 0-5V analog signal) to adjust the motor speed.In this case, you need to:1.

Verify that the shielded 4-wire cable has at least two 18 AWG wires suitable for 24V DC at the expected current draw of the motor.
2. Verify that the other two wires in the shielded cable are 22 AWG or larger.3. Ground the shield properly.Potential Issues



Cable Diameter

The shielded cable might be physically larger or less flexible than the original cable, making it difficult to fit in tight spaces.

Connectors

You might need different connectors to terminate the shielded cable.


Miswiring

Carelessly wiring the replacement cable incorrectly can damage equipment.

Recommendation


Consult the Equipment Documentation

Check the manufacturer's specifications for the original cable and acceptable replacements.2.

Consult an Electrician or Qualified Technician

If you're not comfortable with electrical wiring and safety practices, get professional help.3.

Test Thoroughly

After installation, thoroughly test the system to ensure it's working correctly.

In summary

A shielded 4-wire cable can often be used, but

never compromise on wire gauge (especially for power)
, voltage rating, and proper shield grounding. Always prioritize safety. If unsure, consult an expert. Flag for review

Previous Question Next Question