Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 10 volt dimming

User: stew, Location: federal way,washington

Asked on: Thursday, October 16, 2025 at 10:44 pm EDT
Answered on: Thursday, October 16, 2025 at 10:45 pm EDT

Question: Been off the forum for a long while due to health issues. Back in the saddle again.Just did a large retrofit of 30 year old troffers.120 units.The technology has ran past this old fart. Does anyone know of an inexpensive way to dim these buggers. The normal way of course woukd be a driver on the first fixture of 6 in a room and low voltage wiring. With a retro and Mc feeds to all the switches it's a bugger. Any ideas besides 175 $ worth of parts? No real way to feed the low voltage. No emt. .only eat is the feed to the first j box in the array.

Welcome back to the forum! Glad to hear you're feeling better and getting back into work. Retrofitting dimming into an existing system like that can definitely be a headache. You're right, running new low-voltage wiring for traditional dimming can be a major pain in your situation.Here's a breakdown of some approaches, starting with the most likely to work with your existing wiring, along with their pros, cons, and ballpark cost (keeping in mind prices can vary greatly)

1. Wireless Dimming Control (Smart Lighting)
How it works

Replaces existing switches with smart switches that communicate wirelessly to the LED troffers. The troffers themselves typically need to have compatible drivers. Several options exist, using Wi-Fi, Zigbee, Bluetooth, or proprietary RF protocols.


Pros



No new wiring needed (huge advantage).
Leverages existing power wiring. Relatively easy to install (switch replacements, potentially some driver replacement). Centralized control through a hub or app. You can set schedules, create scenes, and potentially integrate with other smart home systems. Scalable – you can start with a few lights and add more later. Some systems can be controlled remotely. Cons

Can be more expensive initially per fixture than some hardwired options if you were able to easily run the wires. Requires compatible drivers in the LED troffers (this is the BIG question). You'll need to research and verify compatibility. Look for drivers that support 0-10V dimming via wireless control. Reliability depends on the strength of the wireless signal and the quality of the components. Consider a mesh network for best reliability, especially with a large number of fixtures. Security concerns (although reputable systems are generally well-protected). Potential for compatibility issues between different brands or protocols. Stick with a single, well-supported ecosystem.

Approximate Cost

This is highly variable. Figure roughly $50-150 per fixture plus the cost of a hub or controller. A good-quality smart switch might cost $30-50 each.

Key Considerations



Driver Compatibility

This is the MOST important factor. You MUST confirm that the LED troffers you installed have drivers that are compatible with the chosen wireless dimming system. Read the driver specs carefully. Look for terms like "0-10V dimming" or "wireless control compatible." Contact the manufacturer of the LED troffers and ask specifically about wireless dimming compatibility.

Signal Strength

If you have a large space or thick walls, a mesh network system (where each device acts as a repeater) is recommended.


Number of Fixtures

Consider the maximum number of devices that the hub/controller can support.

Brands to Research

Lutron Caséta, Philips Hue, Leviton Decora Smart Wi-Fi, Inovelli (Z-Wave). Also investigate commercial-grade systems designed for larger installations, such as Lutron Vive or Wattstopper Digital Lighting Management (DLM). While more expensive, these are designed for robust performance in commercial settings.

2. Power Line Communication (PLC) Dimming
How it Works

Uses the existing power lines to transmit dimming control signals. Requires special dimming controllers and dimmable LED drivers that are compatible with PLC technology.

Pros

No new control wiring needed. Potentially less expensive than wireless if it works reliably.

Cons



Reliability is highly dependent on the quality of the power wiring and the presence of electrical noise.
Older wiring can be problematic. PLC technology can be sensitive to other devices on the circuit (e.g., motors, computers). Can be difficult to troubleshoot. Limited selection of compatible devices. May require filters to reduce noise. Not as widely used or supported as other methods. Approximate Cost

Difficult to estimate due to limited adoption. Expect to pay a premium for compatible drivers and controllers.


Key Considerations

The age and condition of the wiring. The electrical noise environment. The availability of compatible devices.

3. Step Dimming Ballasts/Drivers (Less Desirable but Cheaper in
some Cases)
How it works: This involves replacing the existing LED drivers with "step dimming" drivers. Step dimming drivers cycle through predetermined light levels (e.g., 100%, 50%, 25%, Off) each time the switch is turned off and back on. Pros



No new wiring at all.
Uses the existing on/off switch. Theoretically inexpensive - just swapping drivers. Cons



Very clunky and unreliable user experience.
Users have to rapidly cycle the switch to get the desired light level. Unpredictable. People will get annoyed very quickly. May not be compatible with all existing switches. Often doesn't provide truly smooth dimming. Limited dimming levels. Approximate Cost

$20-$40 per driver + labor.

Key Considerations

Considered a very outdated method. Customer satisfaction will likely be low. Only consider this if your client absolutely cannot afford anything else and just needs some level of dimming control.

Recommendations


Prioritize Driver Compatibility

The VERY first thing you need to do is determine if the existing LED troffer drivers are compatible with any dimming control method. Get the driver model number and research it online, or contact the manufacturer directly. Look for drivers that support 0-10V dimming or have specific wireless dimming compatibility.2.

Wireless Dimming (if drivers are compatible)

If the drivers are compatible, a wireless dimming system is likely the most practical solution, despite the higher upfront cost. It avoids the headache of running new wiring.3.

Power Line Communication (PLC)

Only consider this if wireless is not an option AND you are willing to accept the risk of poor reliability.4.

Step Dimming: Avoid this if at all possible!
Only use this as a last resort.

Important Notes



Local Codes

Ensure that any dimming system you install meets local electrical codes and regulations.


Professional Installation

If you're not comfortable working with electrical wiring, hire a qualified electrician to install the dimming system.*

Testing:
Thoroughly test the dimming system after installation to ensure that it is working properly and that there are no compatibility issues.Good luck with your retrofit project! Let me know if you have any other questions. Flag for review

Previous Question Next Question