User: mikejohnson, Location: NY
Asked on: Monday, October 20, 2025 at 2:59 pm EDT
Answered on: Monday, October 20, 2025 at 3:06 pm EDT
Question: Hello, I'm looking for help selecting a drum switch for a motor and have a few questions about it.Motor: WEG W22 single phase (cat ID 00318ES1B184TC-W22) - 3 HP, 115/208-230 VWhen looking into drum switches, most have a HP rating of 1.5 @ 115V and 3 @ 230V. In my case, I will be plugging this motor/switch into a typical 120V outlet. The data sheet for the motor gives a output of 3 HP with a rated voltage of 115/208-230 V. Should I assume the 3 HP output from the data sheet is at 230V and less for 115V? Or should I be looking for a drum switch rated for 3 HP @ 115V? Would there be any issue with drum switch with a lower HP rating than motor output?Drum switch in mind:Drum Switch
You've hit a common point of confusion when dealing with motors and drum switches. Let's break it down
Understanding Motor HP and Voltage
HP is Related to Torque and Speed
Horsepower is a measure of mechanical power. It's directly related to the torque the motor can produce and the speed at which it can produce it.
Lower Voltage, Lower Current (Usually)
When a motor is wired for lower voltage (115V instead of 230V), it typically draws more current to produce the same horsepower (or less, depending on the specific motor design). This is because power (Watts) is Voltage x Current. To get the same Watts (which roughly translates to HP), if you lower the Voltage, you have to increase the Current.
Motor Data Plate is Key
The motor's data plate is your best source of information.
Analyzing Your Specific Motor (WEG W22 00318ES1B184TC-W22)1. Data Sheet Check
Let's carefully look at the WEG W22 datasheet. It should specify the full load amperage (FLA) for both 115V and 230V operation. You mentioned the datasheet lists 3HP at 115/208-230. It is most likely that 3 HP can be achieved at 230V, but most likely less at 115V.
2.
FLA is Critical
The
Full Load Amperage (FLA) is the most important number when selecting a drum switch. The drum switch must be rated to handle the FLA of the motor at the voltage you are using (115V in your case).
Addressing Your Questions "Should I assume the 3 HP output from the data sheet is at 230V and less for 115V?" Probably, unless the datasheet explicitly states 3 HP at both voltages and provides the corresponding FLA for each. Most single-phase motors wired for 115V will have a lower effective HP output because they aren't running at their peak operating capacity. "Or should I be looking for a drum switch rated for 3 HP @ 115V?" Ideally, yes, if your motor is designed to provide 3 HP at 115V and the drum switch is designed to support it. This is usually where the FLA ratings of both come into play. If the motor is actually only producing 1.5 HP at 115V, then using a 3 HP drum switch may not be necessary. "Would there be any issue with drum switch with a lower HP rating than motor output?" Absolutely! This is the biggest danger. A drum switch with a lower HP rating than the motor's required HP/FLA at your operating voltage will almost certainly fail, and could potentially cause a fire hazard. The switch contacts are not designed to handle the current.
How to Select the Correct Drum Switch1. Get the FLA
Find the FLA for 115V operation directly from the motor's data plate or datasheet.2.
Match or Exceed
Select a drum switch with a HP and AMP rating at 115V that is equal to or greater than the motor's FLA. A little bit of headroom is good, but excessive over-sizing isn't necessary.
Important Considerations Duty Cycle
Consider the motor's duty cycle (how frequently and for how long it will be used). If it's a heavy-duty application, you may want to over-rate the drum switch slightly.
NEMA Rating
Choose a drum switch with a suitable NEMA rating for the environment (e.g., NEMA 4 for wet locations, NEMA 12 for dusty environments).*
Professional Installation
If you are not comfortable working with electrical wiring, consult a qualified electrician.
In summary, prioritize the motor's FLA at 115V over the HP rating alone when selecting your drum switch. The drum switch must be able to handle the current the motor draws at 115V. Good luck! Flag for review