Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: 110.14(A), rule for conductors on a terminal

User: Steve Spiecker, Location: Alabama

Asked on: Monday, October 20, 2025 at 10:15 pm EDT
Answered on: Monday, October 20, 2025 at 10:17 pm EDT

Question: Hey Mike Holt Enterprises, should 110.14(A) read …one conductor ‘end’ or terminal, instead of one conductor or terminal? When someone strips at mid-wire, and wraps a screw, and has what looks like two wires coming out from the screw and no ends, is this permitted by 110.14? In my mind I’m struggling with the power source coming TO this screw may be one conductor, and even though the wire isn’t cut, would the part coming FROM the screw be considered a second conductor, as it’s purpose is feeding out, once it leaves the screw connection?

Okay, this is a great question about a common point of confusion and a potentially dangerous practice. Let's break down 110.14(A) and how it applies to your mid-wire tap scenario.

Understanding 110.14(A) - Electrical Connections110.14(A) requires that electrical connections be made in a way that ensures a reliable electrical and mechanical connection. The key takeaway here is not just about the number of conductors involved, but the reliability of the connection.

The "Mid-Wire Tap" Scenario

You're describing a situation where someone strips insulation from the middle of a wire, wraps that exposed section around a terminal screw, and then effectively uses the continuing wire to feed another point. This is generally not a permitted or safe practice for the following reasons, regardless of whether you interpret it as one conductor or two:1. Compromised Wire Integrity

Stripping the insulation mid-wire weakens the conductor. Bending and wrapping it around a screw further stresses the copper. This can lead to:

Reduced Current Carrying Capacity

The thinned or damaged wire can overheat under load.


Increased Resistance

A poor mechanical connection creates resistance, generating heat and potentially causing a fire.

Mechanical Failure

The wire can break at the point of stress, leading to an open circuit.2.

Poor Contact Area

Wrapping a wire around a screw in this manner provides a very small and unreliable contact area. This exacerbates the issues of resistance and heat.3.

Lack of Secure Termination

Terminal screws are designed to clamp a conductor that's properly sized and stripped. Simply wrapping the wire doesn't provide the secure, consistent pressure needed for a reliable connection.4.

Violation of Listing and Labeling

Devices are listed and labeled based on specific termination methods. Your "mid-wire tap" is likely not an approved method for any listed terminal.

Addressing the "One Conductor" vs. "Two Conductors" Interpretation


While your question is valid about how to interpret "conductor or terminal" in the context of this tap, it's almost a moot point. Even if you argue it's just
one continuous conductor (which is a stretch), the quality of the connection is still unacceptable under 110.14(A). The method used simply doesn't provide a reliable, safe, and code-compliant electrical connection.

Why It's Not Safe, Regardless of Semantics

The safety concern comes from the risk of a poor connection that gets hot, causes voltage drop, and becomes a fire hazard. It's about more than just counting conductors; it's about the
quality and reliability of the connection.

What 110.14(A)
Really Means110.14(A) isn't about splitting hairs over whether something is technically one conductor or two. It's about: Using Approved Methods

Employing methods specifically designed and tested for making electrical connections (e.g., wire connectors, properly rated terminals, crimped splices).

Maintaining Conductor Integrity

Not damaging or weakening the conductor during the connection process.


Ensuring Tight and Secure Connections

Providing adequate clamping force and contact area to prevent loosening and overheating.

Using Listed and Labeled Equipment Appropriately

Following the manufacturer's instructions for termination methods.

Acceptable Alternatives to the "Mid-Wire Tap"


If you need to tap into a wire, here are some acceptable and code-compliant methods:
Wire Connectors (e.g., Wire Nuts, Push-in Connectors)

These are specifically designed for splicing wires together. Strip the wires properly and use the correct size connector for the number and gauge of conductors.

Terminal Blocks

These provide a series of terminals for making connections, often used in control panels and junction boxes.


Split Bolt Connectors

For larger conductors, split bolt connectors provide a robust and secure method for tapping into a main conductor.*

Adding a Junction Box

This allows you to make proper splices and terminations in a safe and accessible enclosure.

In Conclusion


The "mid-wire tap" method you described is a dangerous practice that violates the intent of 110.14(A), even if you try to argue that it technically involves only one "conductor." It's crucial to prioritize safety and use approved methods for making electrical connections. Never compromise on the quality and reliability of electrical connections! Flag for review

Previous Question Next Question