Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Substation Design Question

User: faresos

Asked on: Wednesday, October 22, 2025 at 11:47 am EDT
Answered on: Wednesday, October 22, 2025 at 11:48 am EDT

Question: Hello everyone:I’m working on a project involves a design of a substation. The substation area is enclosed by fence and split in half by another fence; one area for the utility metering; the other is for the customer owned 34.5KV GIS switchgear, transformer (34.5KV- 12.47KV), and 12.47KV switchgear. Long story short, the utility company asked us to provide an overhead non fused switch structure in the customer side of the fence before terminating into the GIS 34.5KV switchgear main breaker. My questions:My understanding, based on this configuration, the switch structure will become the service disconnection mean (since it will be owned by the customer). Per NEC 230.91, this switch must have and OC protection device (fuse), correct? If yes, then it will be an issue for us because the utility company told us the maximum fuse size that can be used which will not work for us because it will limit the capacity of the transformer.Does the code provide any exception to allow to have a non-fused switch (Isolated switch) in this case since the GIS switch has a main and located within the same substation yard?Does NEC 110.31 table require us to maintain 15ft clearance from the exposed life part? Does that mean the distance is measured from the actual live part, which is up high, or from the structure pole? We have a very limited space available to install this structure, that’s why a pad mounted gear is not an option.Your thoughts are really appreciated.

Okay, let's break down your substation design challenge and address the NEC implications, especially regarding the overhead switch structure.1. Understanding the Configuration and Key Issues Substation Layout

You have a fenced substation split into utility and customer sides. The customer side contains the 34.5kV GIS, transformer, and 12.47kV switchgear.


Utility Requirement

The utility mandates an overhead, non-fused switch before the 34.5kV GIS main breaker. This is your main point of contention.

NEC 230.91 & Service Disconnecting Means

If the overhead switch becomes the service disconnecting means (since it's customer-owned), NEC 230.91
generally requires overcurrent protection (OCP) as part of or immediately adjacent to the disconnecting means. This is your first major conflict.

Fuse Size Limitation

The utility's maximum fuse size restriction is too low for your transformer's required capacity. This is the core operational problem.

NEC 110.31 and Clearance

You're concerned about the required clearances from exposed live parts and how to measure them, especially with limited space.

2. Analyzing NEC 230.91 and Exceptions


This is where the most critical analysis is needed. NEC 230.91 states:> 230.91 Available Short-Circuit Current. Service equipment shall be suitable for the maximum available fault current likely to be imposed on the equipment.
Interpretation and Potential Exceptions



Is it Really the Service Disconnecting Means? This is key. The utility requires the switch before your 34.5kV GIS breaker. Argument for NOT Being the Service Disconnect: You could argue that the GIS breaker itself is the service disconnecting means because: It's the first disconnecting means after the service point of connection. It provides OCP for the transformer and downstream equipment. It's readily accessible to your personnel. The Non-Fused Switch's Purpose: If this argument holds, the overhead switch is essentially an isolation switch or sectionalizing switch. Its main purpose is to provide a visible break for maintenance or isolation purposes, upstream of the actual service disconnecting means (the GIS breaker).

The Utility's Rationale

You must understand the exact reason why the utility requires the non-fused switch. Is it solely for visible isolation, or is there a specific utility protection coordination strategy involved? Their rationale will significantly influence your code interpretation and negotiation possibilities.

Exception to 230.91? This is a gray area. There isn't a
direct exception that says, "If you have a GIS breaker in the same substation yard, you don't need OCP at the overhead switch." However, you might be able to leverage:

Engineering Judgment and Authority Having Jurisdiction (AHJ) Approval

If you can demonstrate, through a detailed engineering study (short circuit coordination study), that the GIS breaker absolutely provides adequate overcurrent protection for the transformer and the entire system, you might persuade the AHJ and the utility that the overhead switch doesn't require fuses. This is a high-stakes argument and requires solid technical justification. Your documentation has to show how the breaker provides protection equivalent to fuses at the pole.

Specific Utility Requirements

In some areas, the utility itself acts as the AHJ for substation design. If their internal standards explicitly allow a non-fused isolation switch under specific conditions (e.g., with a coordinated breaker system), you may be able to comply.

3. Negotiating with the UtilityThis is crucial. Here's how to approach it:


Clearly Define the Service Point

Agree in writing where the service point is located. Usually, it's the termination of the utility's line. If it's before the overhead switch, your argument is stronger that the GIS breaker is the service disconnect.

Understand Their Rationale

Ask
why they require the non-fused switch and the fuse limitation. Their answer dictates your approach.

Present Alternatives

Propose solutions that meet their concerns while addressing your transformer capacity needs. Options include:

Revised Fuse Size

Can you re-evaluate the fuse size in coordination with the utility? Is there any flexibility, perhaps by using specific fuse characteristics (e.g., time-delay fuses) or a more detailed coordination study?


Adding Fuses in the GIS

Is it possible to add fuses within the 34.5kV GIS switchgear, just after the breaker? This might satisfy both the utility's need for OCP and your capacity requirements.

Breaker Coordination Study

A professional engineering study demonstrating the breaker's adequate OCP is essential. Present this to the utility.


Document Everything

Keep detailed records of all communications, agreements, and justifications.

4. Addressing NEC 110.31 (Clearance Requirements)NEC 110.31 deals with working space and guarding of energized parts:> 110.31(A) Working Space. Sufficient access and working space shall be provided and maintained about all electrical equipment to permit ready and safe operation and maintenance of such equipment.>> (B) Separately Enclosed Equipment. Where equipment is installed in a room or enclosure that is accessible to qualified persons only, the equipment shall be considered guarded because the room or enclosure provides a means of protection from unqualified persons.>> (C) Protected by Location. Live parts shall be considered suitably guarded where they are guarded as described in 110.31(C)(1) through (C)(3).>> (C)(1) Covered or Enclosed. Live parts shall be considered suitably guarded where they are covered, guarded, or placed within a suitable enclosure.>> (C)(2) Permanent Barriers. Live parts shall be considered suitably guarded where they are permanently separated from the working space by a suitable partition or screen arranged so that only qualified persons will have access to the space within reach of the live parts. Any openings in such barriers shall be sized and located so that persons are not likely to contact the live parts.>> (C)(3) Elevation. Live parts shall be considered suitably guarded where they are elevated as follows:>> (1) Where the voltage is 600 volts, nominal, or less, they are elevated so that they are not accessible to unqualified persons.>> (2) Where the voltage is greater than 600 volts, nominal, they are elevated per Table 110.31.Interpretation and Measurement



Clearance Measurement

The clearance required by Table 110.31 is measured from the
exposed live part. In this case, it's the actual energized conductor or terminal.

15-Foot Clearance

For voltages above 751 V nominal to 15 kV nominal, Table 110.31 requires a minimum horizontal and vertical clearance of 15 feet for Qualified Persons.

Limited Space Solutions



Structure Design

Design the switch structure to minimize the horizontal footprint while maximizing vertical height. Carefully position the live parts as high as possible.

Guarding

Consider physical barriers or cages around the live parts,
in addition to elevation, to further restrict access and reduce the required clearance distance. This is often a practical necessity in substations.

Warning Signs

Use clear, prominent warning signs to indicate the presence of high-voltage equipment and the need for caution.

5. Summary and Action Steps
1. Define Service Point

Get clear, written confirmation from the utility of the exact location of the service point.2.

Understand Utility Rationale

Ask why they require the non-fused switch and the fuse limitation.3.

Engineering Study

Commission a detailed short-circuit and coordination study to demonstrate the adequacy of the GIS breaker's OCP.4.

Negotiate with Utility

Present your findings and alternative solutions to the utility. Be prepared to be flexible.5.

AHJ Approval

If necessary, involve the AHJ early in the process and seek their approval for your proposed design.6.

Clearance Design

Carefully design the overhead switch structure to maximize clearances, use guarding, and provide clear warnings.7.

Documentation:
Keep detailed records of all communications, agreements, and justifications.This is a complex situation. By carefully analyzing the NEC requirements, understanding the utility's needs, and presenting well-justified alternatives, you can achieve a safe, compliant, and functional substation design. Good luck! Flag for review

Previous Question Next Question