User: jmellc, Location: Durham, NC
Asked on: Wednesday, October 22, 2025 at 11:40 pm EDT
Answered on: Wednesday, October 22, 2025 at 11:40 pm EDT
Question: I had never worked on rollup doors before my present job. Have only dealt with a few here and wind up letting the door company deal with it. I'm never the one on duty when they come. They work days of course and I'm a night guy. best I can figure is that coils get weak and eventually give out. Door will work intermittently both up and down, then stop. Wil work again after a while. Have any of you worked much on rollups? Any common issues? Any good literature out there?
You're right, rollup doors can be a bit of a mystery until you've worked on them regularly. And you're on the right track with the spring coils being a major culprit. Let's break down common issues, troubleshooting, and resources
Common Issues with Rollup Doors:
Weak/Broken Springs
This is the most common problem. The springs provide the counterbalance, making the door feel lighter and easier to operate. When they weaken or break, the door becomes very heavy, causing strain on the motor (if it's motorized) or making manual operation extremely difficult. You described it perfectly: intermittent operation as the spring is barely doing its job, then failing completely.
Worn/Damaged Guides (Tracks)
The door rolls up and down in these tracks. Over time, they can become bent, corroded, or filled with debris. This causes friction, making the door hard to move, or even causing it to bind.
Motor Problems (If Motorized)
These doors are not always motorized. If yours is motorized, the motor itself can fail. This could be due to a bad capacitor, burnt-out windings, or a faulty control board. Limit switches (which tell the motor when to stop) can also malfunction.
Limit Switch Adjustment
The limit switches may be in need of adjustment.
Loose/Broken Hardware
Look for loose or missing bolts, nuts, and screws. Vibrations from opening and closing can loosen these over time. Also check for damaged or worn rollers.
Obstructions
Something in the track, like a tool that was left there, a broom that was leaned against the door, etc.
Cable Issues
Some rollup doors use cables to assist with lifting, especially on heavier doors. These cables can fray, break, or slip off their drums.
Slats Out of Alignment
The individual horizontal sections (slats) of the door can become misaligned or damaged, causing the door to bind or rub.
Lack of Lubrication
Rollup doors need regular lubrication. Dry tracks, hinges, and rollers increase friction and wear.
Safety Edge Malfunction
Some motorized doors have a safety edge that detects obstructions and stops the door from closing. These can become faulty.
Troubleshooting Steps
Safety First
Always disconnect the power to the motor (if applicable) before working on the door. If you're dealing with springs, understand that they are under tremendous tension and can be dangerous if mishandled. If you're not comfortable working with springs, don't. This is the most dangerous part of the job.2.
Visual Inspection
Start with a thorough visual inspection. Look for broken springs. Are they visibly separated? Check the tracks for damage, bends, or obstructions. Examine the rollers for wear and tear. Inspect the cables (if present) for fraying or looseness. Look for loose hardware. Check that the slats are aligned.3.
Manual Operation Test (Power Off)
Disconnect the motor and try to raise and lower the door manually. How heavy does it feel? If it's excessively heavy, the springs are likely the problem. Does it move smoothly? If not, identify where the friction is coming from. Listen for unusual noises (grinding, scraping).4.
Motor Diagnostics (If Applicable)
If the motor runs but the door doesn't move, check the connection between the motor and the door mechanism. If the motor hums but doesn't turn, it could be a bad capacitor or a jammed mechanism. Check the limit switches. Can you manually activate them? Are they properly adjusted?5.
Lubrication
Lubricate all moving parts – tracks, rollers, hinges, and springs (use a silicone-based lubricant or a dry lubricant to avoid attracting dirt).6.
Spring Tension Adjustment
This is best left to professionals if you are not trained. Adjusting spring tension is how the counterbalance is set. Too little tension, and the door is heavy to lift; too much, and it will fly up on its own.7.
Call a Professional
If you suspect broken springs, serious motor problems, or structural damage, it's always best to call a qualified door repair company. Especially with springs, the risk of injury is high.
Literature & Resources
Manufacturer Manuals
This is the best place to start. Find the manufacturer and model number of your rollup door. You can often find manuals online. These manuals contain detailed information about the door's components, operation, maintenance, and troubleshooting.
DASMA (Door and Access Systems Manufacturers Association)
DASMA is a trade association that provides safety and technical information about garage doors and other types of doors. Their website has resources for homeowners and professionals.
Specific Advice Based on Your Situation
Document Everything
Keep a detailed log of the issues you're seeing, what you've tried, and the results. This will be helpful for the door company when they come.
Ask Questions
When the door company comes to fix the door, ask them questions! Pick their brains. Ask them about the specific problem they're addressing, the cause, and how to prevent it in the future.
Consider Preventative Maintenance
Talk to your management about setting up a preventative maintenance schedule for the rollup doors. Regular lubrication and inspections can help prevent major problems.
Observe
Pay attention to how the door operates when it's working correctly. This will help you identify when something is starting to go wrong.
Important Reminders
Springs are dangerous! Never attempt to repair or adjust springs unless you are properly trained and have the correct tools. Safety First! Always disconnect power before working on electrical components. Wear appropriate safety gear (eye protection, gloves).* Don't force anything! If something is stuck, don't force it. Find out what's causing the obstruction.By combining these troubleshooting steps with a bit of research and on-the-job learning, you'll become more confident in your ability to handle rollup door issues. Good luck! Flag for review