Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Voltage bleeding through relay?

User: iwirehouses

Asked on: Thursday, October 23, 2025 at 5:03 pm EDT
Answered on: Thursday, October 23, 2025 at 5:03 pm EDT

Question: I just got hired to do the wiring to replace a pump and floats in a septic tank. Wasn’t a bad job honestly. But there’s a controller inside the house where all the floats and pump run to. With an alarm on it. Everything‘s working fine. Except the pump turns on via a relay. With the coil, not energized in the relay, there is always 50 volt to the hot wire going out to the pump. Once the relays energized 120 V goes through the relay to the pump. And it turns on. Everything works fine. But I’m suspicious why there is 50 V on the laod side of the relay without the coil being energizer. The neutral doesnt bleed trough the relay at all. Everything works fine. Wondering what I’m missing. Or if I should be concerned.

Okay, this is a very common and important question. Here's a breakdown of what's likely happening and what you should consider

Understanding What's Happening: Induced Voltage (Ghost Voltage)

What you're almost certainly seeing is induced voltage, also known as ghost voltage or phantom voltage. Here's how it works: Capacitive Coupling

Wires running parallel to each other, especially over longer distances, can act like a capacitor. The energized hot wire in the house, running parallel to the wire going to the pump, can induce a voltage in the unenergized pump wire. The longer the parallel run, the greater the induced voltage. Think of it like a weak wireless signal.


High Impedance Multimeters

Modern digital multimeters (DMMs) have very high input impedance. This means they require very little current to register a voltage. Even a small amount of induced voltage can be easily detected by these meters. Older analog meters, with lower impedance, would typically load the circuit enough to bleed off this induced voltage and not register it.

Why It Works (Even With Induced Voltage)



Low Current Capacity

The induced voltage has very little current behind it. It can register on a voltmeter, but it can't deliver any significant power.


Pump Requires Amperage

The pump needs a significant amount of current to start and run. The induced voltage simply doesn't have the "push" (amperage) to do anything.

Why It's (Probably) Not A Problem (In This Case)



System Functionality

You've confirmed that the system is operating correctly. The pump starts and stops as intended when the relay is energized.


No Leakage Current

You've verified that the neutral isn't leaking through. This is crucial. A neutral leak could be a safety hazard.

Voltage Drops Under Load

The 50V disappears as soon as the relay kicks in because the energized relay and pump create the low resistance path the current uses.

Important Considerations and Things To Check (Safety First!)


Confirm Your Meter

Just to be sure, test the same cable that has 50V with a low-impedance meter. If the low-impedance meter shows 0V, this confirms it’s a phantom voltage.2.

Neutral Wire

Make absolutely sure that the neutral wire is connected at the panel and not shorted anywhere. A floating neutral can create very strange voltage readings.3.

Grounding

Verify that the pump itself is properly grounded. A good ground connection can help bleed off some of the induced voltage.4.

Wire Run

If possible, check the physical routing of the wire going to the pump. Is it running parallel to other energized wires for a significant distance? Is it close to other electrical equipment? While you can't always change the routing, knowing the path can help you understand the induced voltage.5.

Relay Condition

While it sounds like the relay is working correctly, it's worth visually inspecting it for any signs of damage, corrosion, or loose connections. A failing relay
could eventually cause problems.6.

Client Awareness

Explain to the homeowner what you've found. Let them know it's likely induced voltage and, as long as the system functions correctly, it's not a cause for immediate concern. Document your findings in your invoice.

When to Be
More Concerned



Significant Current Flow

If you measure current flow along with the voltage, that's a problem. This indicates a leakage path and a potential shock hazard. Use a clamp meter to measure current on the wire when it's supposed to be off. You shouldn't see any significant current (milliamps).

System Malfunction

If the pump starts acting erratically, fails to start, or runs continuously, then you'll need to investigate further.


Shock Hazard

If you ever feel a tingle or shock when touching the pump housing or the wires, immediately shut off the power and investigate. This is a serious safety issue.

Voltage is Higher Than Expected

50V is on the high side for induced voltage, though not unheard of. Higher voltages
might indicate a more significant issue. Anything over 60V should be treated with extra caution.

In summary:


The 50V is likely induced voltage, which is common, and often not a problem as long as the system functions correctly and there's no leakage current. Follow the steps above to verify your assumptions.
Disclaimer: I am an AI Chatbot and not a qualified electrician. The information provided is for informational purposes only and does not constitute professional electrical advice. Consult a qualified electrician for all electrical work.* Flag for review

Previous Question Next Question