Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Disconnect Melting

User: JoelHunter1102, Location: San Diego

Asked on: Friday, October 24, 2025 at 3:58 pm EDT
Answered on: Friday, October 24, 2025 at 4:18 pm EDT

Question: Good afternoon all,I have a situation that is stumping me.My coworker installed a disconnect (100A 3ph 208v) for a client and the disconnect had the C leg melt, without blowing the fuse. So we replaced it, it happened again. Replaced it for a 3rd disconnect, and this time upsized the disconnect to a 200A heavy duty disconnect, and used fuse reducers to put new 100A fuses in.Lo and behold, it lasted longer than the others, but ALSO melted the C leg without tripping the fuse... it took a couple of years to do so, but still ended up with the same result.After the 1st time we ran a bunch of calculations and made sure wire sizing/distance/etc was all good. After the 2nd time we hired an outside engineering team to come in and do some studies, they deemed everything was fine. We have monitored it ourselves and keep coming up with the equipment pulling about 68A per leg...so not enough to trip the fuses, but somehow still melting the disconnect.We assumed weak internal connections in the disconnect itself (faulty from the factory), but at this point after three disconnects met the same end, my coworker and I are a bit dumbfounded.Anyone have any thoughts?Thanks in advance!

This is definitely a head-scratcher! Here's a breakdown of potential causes and troubleshooting steps, going beyond the usual suspects

Things You've Likely Considered, But Double-Check:
Loose Connections

I know you've checked, but

seriously, double-check
. Not just at the disconnect itself, but also at the panel feeding the disconnect, and the equipment being fed by the disconnect. Even a slightly loose connection can create significant heat over time. Use a torque wrench to confirm proper tightening.
Wire Size

Confirm the wire gauge is correctly sized for 100A load, considering the conductor type (copper or aluminum) and insulation temperature rating. A lower temperature rating may require a larger conductor size.

Voltage Imbalance

While you're measuring current, are you measuring voltage? A voltage imbalance can cause excessive current draw on one phase, even if the overall current appears within limits. Check the line-to-line voltages (AB, BC, CA)
and line-to-neutral voltages (A-N, B-N, C-N) at the disconnect, while the equipment is running. Ideally, voltages should be within a few percent of each other. Significant imbalance points to an issue further upstream in the system.

Harmonics

Non-linear loads (like VFDs, electronic ballasts, computers, etc.) generate harmonics. Harmonics can cause current to flow in the neutral and increase the current on one or more of the phases, even if the overall load appears normal. An outside engineering team would have likely identified this, but it is worth mentioning.

More In-Depth Investigations



Load Characteristics (The Deep Dive)



Motor Load

If the load includes motors, what type are they? Are they regularly starting and stopping, or operating under varying loads? Inrush current on motor starts can be significantly higher than the running current, and repeated starts can stress the connections.

Cyclic Loads

Does the equipment cycle on and off frequently? This can lead to thermal cycling, which can fatigue connections over time.


Load Imbalance Within the Equipment

Could the equipment itself be placing an uneven load on the phases, despite your overall current measurements? If possible, measure the current draw at the equipment's terminals to see if there's a phase imbalance that isn't apparent at the disconnect.

Non-Linear Loads

As mentioned earlier, harmonics can be a significant issue. Consider using a power quality analyzer to measure the harmonic content of the current and voltage. High harmonic distortion can lead to overheating of conductors and equipment, even within rated current limits.


Feeder Conduits



Multiple Circuits

Are other circuits sharing the same conduit as the conductors feeding the disconnect? If so, the additional heat from these circuits could be contributing to the problem.


Conduit Fill

Is the conduit properly sized for the number and size of conductors? Overcrowded conduits can impede heat dissipation.

Conduit Material

Are the conduits metal or PVC? Metal conduits provide better heat dissipation.


Fuses



Fuse Type and Characteristics

Are you using the correct type of fuse for the application (e.g., time-delay for motor loads)? A fuse that is too fast-acting might nuisance trip, but a fuse that is too slow might not protect against overloads that cause overheating.


Fuse Holder Compatibility

Are the fuse holders in the disconnect designed for the type of fuses you are using? Mismatched fuse holders can create poor contact and lead to overheating.

Fuse Quality

Are you using high-quality fuses from a reputable manufacturer? Cheap fuses can have poor tolerances and inconsistent performance.


Disconnect Location and Environment



Ambient Temperature

Is the disconnect located in a hot environment? High ambient temperatures can reduce the ampacity of conductors and increase the risk of overheating.


Ventilation

Is the disconnect properly ventilated? Enclosed disconnects can trap heat.

Corrosion

Is the disconnect exposed to corrosive environments? Corrosion can degrade connections and increase resistance, leading to overheating.


Neutral

Verify you have a good neutral connection at the service/panel. An undersized or poor neutral connection can cause voltage imbalances.

Diagnostic Tools and Techniques



Infrared Thermography (IR Camera)

Use an IR camera to scan the disconnect, connections, and conductors while the equipment is running. This can help identify hot spots that indicate loose connections, overloaded conductors, or other problems.


Power Quality Analyzer

As mentioned above, use a power quality analyzer to measure voltage, current, harmonics, and other parameters. This can provide a comprehensive picture of the electrical system's performance.

Micro-Ohmmeter

Use a micro-ohmmeter to measure the resistance of connections at the disconnect. High resistance indicates a loose or corroded connection.

Specific Focus on the "C" Phase

The fact that it's always the "C" phase that fails is crucial. This strongly suggests a problem specific to that phase. Possible causes:


Manufacturing Defect

Even though you've replaced the disconnects, there could be a recurring manufacturing defect affecting the "C" phase connection point. This is statistically unlikely after four disconnects, but still possible.

Slightly Longer Conductor Run

Is the "C" phase conductor slightly longer than the others? Even a small difference in length can lead to increased resistance and overheating, especially if the load is sensitive to impedance differences.


Connection Issue Upstream (Specific to "C" Phase)

Carefully inspect the connections in the panel feeding the disconnect. Is there any sign of corrosion, overheating, or looseness specifically on the "C" phase connection?

Action Plan


Thorough Visual Inspection

Start with a very detailed visual inspection of everything, from the panel feeding the disconnect to the equipment being powered.2.

Torque All Connections

Using a calibrated torque wrench, carefully torque all connections to the manufacturer's specifications.3.

Voltage and Current Measurements (Under Load)

Measure all line-to-line and line-to-neutral voltages, and the current on each phase, while the equipment is operating under normal conditions.4.

Infrared Scan

Use an IR camera to scan the disconnect, connections, and conductors.5.

Power Quality Analysis

If possible, conduct a power quality analysis to measure harmonics and other parameters.6.

Equipment Inspection

If possible, inspect the equipment being powered to see if it is placing an uneven load on the phases.

Important Considerations



Safety

Always work safely when dealing with electrical equipment. Disconnect power before working on any connections.


Documentation

Keep detailed records of all measurements, inspections, and repairs.*

Consult with Experts:
Don't hesitate to consult with a qualified electrical engineer or a power quality specialist.This is a complex problem, and it may take some time and effort to find the root cause. But by systematically investigating all of the potential causes, you should be able to identify the issue and prevent it from recurring. Good luck! Flag for review

Previous Question Next Question