Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Two generators, each on separate MTS?

User: dvnwvt, Location: Vermont

Asked on: Monday, October 27, 2025 at 10:10 am EDT
Answered on: Monday, October 27, 2025 at 10:37 am EDT

Question: I have an existing 240/120V manual transfer switch with outside generator hookup installed feeding a handful of loads. My electric vehicle has with a 1800 W / 120V 'Vehicle to Load' adapter. I'd like to add a 2nd MTS to supply a few 120V loads from the EV, which would give me a backup fuel source. Also my generator died and by moving 120V loads to the EV, I can go with a smaller conventional generator on the existing MTS. From what I've read I think there are no problems with the concept? Just looking for any red flags. (Note - I'm still digging into whether the EV's inverter has a floating neutral and any ramifications of that). Schematic

Okay, let's analyze your plan to use a second manual transfer switch (MTS) to power some 120V loads from your EV's vehicle-to-load adapter. You're essentially creating a parallel backup power system, which is perfectly viable with the right considerations.

Here's a breakdown, addressing potential red flags and key things to consider



1. Concept Viability



Conceptually Sound

Using your EV as a supplemental power source is a smart way to leverage existing resources. Splitting the critical loads between the EV and a smaller generator (on the existing MTS) makes sense for flexibility and potentially better fuel efficiency.

2. Potential Red Flags and Key Considerations



Neutral Bonding (MOST CRITICAL)

You are right to be concerned about the neutral bonding in the EV's inverter.

THIS IS THE BIGGEST POTENTIAL HAZARD.
Floating Neutral

Many portable inverters (and some vehicle-to-load systems) have a
floating neutral when not connected to shore power. This means the neutral conductor is not bonded to ground within the inverter.

Implications of a Floating Neutral



Safety Hazard

Without a properly bonded neutral, the voltage on your circuits can float to dangerous levels. This can cause equipment damage, electric shock, and even fires.


GFCI Malfunction

Ground Fault Circuit Interrupters (GFCIs) rely on a bonded neutral to detect ground faults and trip. They will not function correctly with a floating neutral.

Testing for a Floating Neutral

Use a multimeter to measure the voltage between the neutral conductor of the EV's adapter and the ground conductor of the adapter when the EV is
not connected to shore power (e.g., plugged into a charging station). If you measure anything other than 0V, you likely have a floating neutral. Double-check this with the vehicle manufacturer's documentation or technical support.



Solution (IF Neutral is Floating)

If your EV's inverter has a floating neutral, you

MUST bond the neutral to ground only at the inlet of the second MTS.

DO NOT BOND NEUTRAL TO GROUND ELSEWHERE IN THE SYSTEM.

How to Bond

Create a short jumper wire (12 AWG or thicker) from the neutral terminal on the input side of your second MTS to the ground/earthing terminal on the input side of the second MTS. This establishes the required neutral-ground bond. It
only needs to be done within the second MTS enclosure.

Important Considerations When Bonding

The neutral bond should be established only at

one single point in your backup power system.
Having multiple neutral-ground bonds creates a ground loop, which can cause circulating currents and other problems. Since the existing MTS likely has a neutral-ground bond at the generator inlet, you do not want to establish another one elsewhere.

Backfeeding Hazards

Ensure your two MTS's are interlocked so you can never backfeed the grid!


Load Calculation and Power Limits



EV Capacity

You state your EV provides 1800W at 120V. That's 15 amps (1800W / 120V = 15A). Make sure the total load you connect to the second MTS doesn't exceed this limit. Overloading can damage the EV's inverter.


Existing MTS Capacity

Also ensure your existing MTS and generator can handle their respective loads.

Wiring and Circuit Protection



Wire Gauge

Use appropriate wire gauge for the amperage you'll be carrying. 14 AWG is typically good for 15A circuits, but check local codes.

Circuit Breakers

Use appropriately sized circuit breakers in both the EV-fed panel and the existing generator-fed panel. 15A circuit breaker on the output of the 2nd MTS is appropriate for 15A from EV.


Voltage Drop

Long wire runs can cause voltage drop, especially under load. Use a thicker wire gauge or shorten the wire run to minimize voltage drop. Measure voltage under load at the farthest outlet.

GFCI Protection



Install GFCI Protection

Circuits in bathrooms, kitchens, outdoors, and other locations where water is present must be GFCI protected.

Compatibility with Inverter

Ensure the EV's inverter and the GFCI outlets are compatible. Some inverters can cause nuisance tripping of GFCIs. Test your GFCI outlets after the system is installed.


Extension Cords

Minimize the use of extension cords. If you must use them, use heavy-duty extension cords of the appropriate gauge.

EV Start-Up Load Consideration

The EV is rated for a
continuous 1800W load. Some appliances have high inrush currents at start-up (e.g., refrigerators, air conditioners). These can overload the EV temporarily. Avoid connecting appliances with high inrush currents to the EV unless you know it can handle the surge.

Is the EV output modified sine wave or pure sine wave? Sensitive electronics such as plasma TV's and electronics with dimmer switches may require pure sine wave input3. Schematic Analysis

The schematic helps to visualize your plan. However, it's crucial to include the neutral bonding detail near the inlet of the second MTS (if required) and make sure the grounding is 100% clear to avoid confusion.

4. Code Compliance



Local Codes and Permits

Check your local electrical codes and permit requirements before starting any electrical work. Improper wiring can create safety hazards and code violations.

Qualified Electrician

If you are not experienced with electrical work,
hire a qualified electrician to install the MTS and make the necessary connections.

Steps to Take


Confirm EV Neutral Status

Absolutely confirm whether your EV's inverter has a floating or bonded neutral when not connected to shore power. Contact the vehicle manufacturer's technical support if you are unsure.2.

Neutral Bonding (If Required)

If the neutral is floating, implement the neutral-to-ground bonding at the inlet of the second MTS as described above.3.

Load Calculation

Accurately calculate the load you'll be putting on the EV and the existing generator.4.

Wiring and Protection

Ensure all wiring and circuit protection are appropriately sized.5.

Testing:
* After installation, test the system thoroughly, including voltage measurements under load and GFCI functionality.By carefully considering these points, you can safely and effectively use your EV as a backup power source. The neutral bonding issue is the most critical aspect, so ensure it's addressed correctly. Flag for review

Previous Question Next Question