Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Does someone make a fitting that can mate a D-sub connector to a MC cable?

User: Installer, Location: DesMoines, Washington

Asked on: Monday, October 27, 2025 at 11:55 am EDT
Answered on: Monday, October 27, 2025 at 11:55 am EDT

Question: Does someone make a fitting that can mate a D-sub connector to a MC cable?

You won't find a single, off-the-shelf "fitting" that directly connects a D-sub connector to MC (Metal-Clad) cable. These are very different types of connections, designed for different purposes.Here's why and how you can achieve the connection in a safe and compliant manner

Why a Direct Fitting Doesn't Exist:
Purpose

D-sub connectors are for signal or data connections (low voltage, low current). MC cable is for carrying power (higher voltage, higher current). The insulation and grounding requirements are different.


Mechanical

D-subs are typically panel-mounted or attached to a PCB. MC cable is designed to be secured to junction boxes or enclosures.

Safety Standards

Mixing signal and power wiring improperly can be dangerous and violate electrical codes.

How to Connect D-sub Signals Carried within MC Cable

The key is to properly transition from MC cable to the D-sub connector while maintaining grounding, insulation, and code compliance. Here's the general process:1.

Bring MC Cable into an Enclosure (Junction Box)

This is the fundamental step. Use an MC cable connector (like a screw-in or squeeze connector) approved for that cable size to enter a metal or approved plastic junction box. Ensure the connector is properly tightened to ground the MC cable armor.2.

Terminate the Conductors within the Enclosure



Power Conductors

If the MC cable is carrying power in addition to the signals for the D-sub, terminate those power conductors according to code. This might involve wire nuts, terminal blocks, or another appropriate connection method for the voltage and current involved.

Signal Wires

If you are using the MC cable for physical protection of signal wires:

Use appropriate gauge, low-voltage, insulated wire inside the MC cable. Terminate these wires inside the enclosure using terminal blocks, wire splices, or other secure methods. Do not directly connect the D-sub to the wires coming directly out of the MC cable.3.


Transition to the D-sub Connector



Cable Run

Run appropriately shielded, low-voltage cable (e.g., multi-conductor shielded cable) from the terminal blocks or wire splices inside the enclosure to the D-sub connector. This cable should be sized correctly for the signals it will carry. Use strain relief as needed.

D-sub Connector Mounting

The D-sub connector is typically mounted in one of these ways:


Panel Mount

Mount the D-sub connector on the junction box or an adjacent panel, using the appropriate panel-mount hardware.

Cable Assembly

Create a cable assembly using a D-sub connector. The wires from the enclosure can be spliced or terminated to the wires in this D-sub cable assembly. Ensure proper strain relief where the cable exits the enclosure.4.

Grounding

This is critical!


MC Cable Ground

The MC cable armor must be properly grounded back to the electrical panel. The MC cable connector should make solid contact with the cable armor and the junction box.

Shielded Signal Cable Ground

If you're using shielded signal cable, ground the shield
only at one end, typically at the enclosure end. This prevents ground loops. The D-sub shell should be grounded as well if it's designed to be.

Example Scenario

Let's say you want to run a sensor signal (using low voltage wires) from a remote location back to a control panel, using MC cable for physical protection.1. MC cable enters a junction box near the sensor.
2. The sensor wires, run
inside the MC cable, are connected to terminal blocks within the junction box.3. A shielded cable runs from those terminal blocks to a D-sub connector mounted on the junction box.
4. The MC cable armor is grounded. The shield of the signal cable is grounded at the enclosure, and the D-sub shell is grounded (if applicable).


Important Considerations



Electrical Codes (NEC in the US, CEC in Canada, etc.)

This is not optional! All electrical work must comply with local electrical codes. If you're unsure, consult with a licensed electrician.

Voltage and Current

Ensure that all components (enclosure, connectors, wire, terminal blocks) are rated for the voltage and current they will be carrying.


Shielding

Use shielded cable for signal wires to minimize interference.

Strain Relief

Use strain relief on all cables entering and exiting the enclosure to prevent wires from being pulled out of their connections.


Enclosure Rating

Choose an enclosure (junction box) that is rated for the environment (e.g., NEMA rating for water and dust resistance).

Professional Help:
If you are not comfortable working with electrical wiring, hire a qualified electrician*.In summary, you can't directly connect an MC cable to a D-sub. Instead, use a junction box and other appropriate connectors to safely transition from MC cable to the signal wires connected to the D-sub, maintaining proper grounding and insulation at all steps. Flag for review

Previous Question Next Question