Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Solar interconnection tap space issue.

User: JP23, Location: California

Asked on: Wednesday, October 29, 2025 at 1:12 pm EDT
Answered on: Wednesday, October 29, 2025 at 1:13 pm EDT

Question: The scenario is a 277/480 3 ph. 4w. utility side bus tap to a 1200 amp disconnect for a solar installation. The available spacein the switch gear for the taps does not appear large enough for all of the parallel conductorsrequired. There is a single 10 ft. 3r gutter spanning over each termination point with myers hubs and nipples.The project engineer is saying that any welding wire will suffice and 4/0 will carry 400 amps.I have never seen this in any permanent building wiring scenario and am questioning it. I did finda post where someone said if the welding wire had the RHH/RHW rating itwould be acceptable to use. Any advice on this would be appreciated.

You're right to be highly skeptical. The engineer's assertions are generally incorrect and raise serious safety and code compliance concerns. Here's a breakdown of the issues

1. Welding Cable for Permanent Wiring is Almost Never Acceptable
NEC 400.4

This section strictly limits the uses of flexible cords and cables (which includes welding cable) for permanent wiring. Generally, they are

not
allowed as a substitute for building wire in a permanent installation like you describe.
Welding Cable Design

Welding cable is designed for high flexibility and portability. Its insulation is usually not rated for the same environmental conditions or longevity as building wire. While some welding cable might be RHH/RHW rated, that rating alone doesn't automatically make it suitable for permanent building wiring per the NEC.

Conduit Fill

Welding cable has a larger outside diameter than THHN/XHHW for the same ampacity. This can cause serious conduit fill issues, violating NEC Chapter 9, Table 1 and beyond. You may not be able to get the required number of conductors in the nipples.


Terminations

Welding cable is often terminated with crimped lugs specific to the cable's stranding. These lugs may not be listed for use with the equipment in the switchgear.

Long-Term Durability

Welding cable, even RHH/RHW-rated, is not designed for the same 30+ year lifespan expected of building wire in a permanent installation.

2. Ampacity of 4/0 Wire
NEC Table 310.16

This is the table to consult for ampacity. For copper 4/0 wire with 75°C insulation (like THHN/XHHW which is common), the ampacity is typically 230 amps when installed in a raceway or cable. It is absolutely NOT 400 amps. The Engineer is pulling numbers out of thin air.

Derating Factors

Keep in mind that ampacity needs to be further derated based on:


Ambient Temperature

If the ambient temperature exceeds 30°C (86°F), you must apply correction factors (NEC Table 310.15(B)(1)).

Number of Conductors in a Raceway

If you have more than three current-carrying conductors in a raceway or cable, you must apply adjustment factors (NEC Table 310.15(C)(1)). This is very likely to be an issue with multiple parallel runs.


Termination Temperature

The termination points in the switchgear and at the solar disconnect might be rated for only 60°C or 75°C. You MUST use the lower of the conductor insulation rating or termination rating when determining ampacity per NEC 110.14(C).

3. Gutter and Tap Space Concerns
Gutter Sizing

The 10-foot gutter might not be adequately sized for the number and size of conductors, splices, and bending radius required. NEC Article 366 covers wireways (gutters) and provides rules for sizing.


Tap Rules

If this truly is a tap, NEC 240.21 provides VERY specific rules about the length and ampacity of the tap conductors. The Engineer's "anything goes" attitude is dangerous.

Working Space

You must have adequate working space around the equipment (NEC 110.26). This includes the space for safely installing and maintaining the connections.


Manufacturer's Instructions

The switchgear and disconnect manufacturer's instructions must be followed precisely. These often specify conductor type, size, and termination methods.

4. What To Do
1. Document Your Concerns in Writing

Immediately document your concerns in writing to the project engineer and your superiors. State clearly that you believe the proposed method violates the NEC and industry best practices and presents a safety hazard. This protects you if something goes wrong.2.

Request Written Justification

Demand the engineer provide written justification (including specific NEC references) for using welding cable and claiming 4/0 wire can carry 400 amps. Do not proceed without this.3.

Perform Code Calculations

Do the necessary calculations yourself to determine the correct conductor size, conduit fill, gutter size, and tap rules based on the NEC. Present these calculations to the engineer.4.

Consult with a Qualified Electrical Engineer

If the project engineer is unwilling to correct the design, consult with another qualified electrical engineer who specializes in power systems design and NEC compliance.5.

Involve the Authority Having Jurisdiction (AHJ)

If the situation remains unresolved and you believe the design is unsafe or non-compliant, contact the local electrical inspector (AHJ) and request their input.6.

Consider Alternatives to Parallel Conductors

Could you possibly use larger conductors and avoid paralleling? Could you upgrade the switchgear to one with more termination space? These are usually the best solution.

In summary, the engineer's claims are likely incorrect and unsafe. You are right to be concerned. Prioritize safety, follow the NEC, and get a second opinion from a qualified professional if necessary.
Don't let schedule pressure or cost-cutting compromise safety and code compliance. Flag for review

Previous Question Next Question