Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: MC Cable

User: Jimmy7, Location: Boston, MA

Asked on: Friday, October 31, 2025 at 7:10 am EDT
Answered on: Friday, October 31, 2025 at 7:10 am EDT

Question: Is it permissible to drill a hole in an existing interior cinder block wall and come in the back of a 4” square with MC cable?

Yes, it is generally permissible to drill a hole in an interior cinder block wall and run MC cable into the back of a 4" square box, provided you follow the relevant codes and best practices. Here's a breakdown of the key considerations

1. Code Compliance (NEC - National Electrical Code):
Support and Securing (NEC 330.30)

The MC cable needs to be properly supported and secured. You'll need to use appropriate MC cable straps or clips within a certain distance of the box and at regular intervals along the run (typically every 6 feet horizontally and 10 feet vertically). If the MC cable is run horizontally in a bored hole through framing members, it may be considered supported and secured in some jurisdictions. Check with your local electrical inspector.


Bending Radius (NEC 330.24)

Avoid sharp bends in the MC cable. The minimum bending radius is typically five times the outside diameter of the cable. Make sure there is sufficient room inside the box to avoid too sharp of a bend.

Connectors (NEC 314.17)

You
must use an approved connector where the MC cable enters the 4" square box. This connector serves multiple purposes:

Securing the Cable

Holds the cable firmly in place.

Protecting the Cable

Prevents the cable from being damaged by the edge of the knockout or hole.


Providing Grounding

Ensures a proper ground connection (especially important for MC cable). Use a connector specifically listed for grounding.

Box Fill (NEC 314.16)

Make sure the 4" square box is large enough to accommodate the number of conductors, devices (e.g., receptacles, switches), and MC cable connectors that will be inside. Overfilling a box is a common code violation and can create a fire hazard. A standard 4" square box is typically okay for simple circuits with few devices, but larger boxes or extension rings might be necessary for complex wiring.


Grounding (NEC 250)

The metal armor of MC cable must be properly grounded. The MC cable connector you use is crucial for this. It needs to be listed for grounding and provide a reliable connection to the box. The box itself must also be grounded, usually through the grounding wire in the MC cable, connected to a grounding screw in the box.

Firestopping (NEC 300.21)

If the hole you drill penetrates a fire-rated wall, you
must properly firestop the opening after running the MC cable. Use a listed firestopping material appropriate for the wall type and the size of the opening. This is essential to maintain the fire-resistance rating of the wall.

Penetration Depth and Cinder Block Integrity

Consider the structural integrity of the cinder block wall. Avoid drilling excessively large holes or drilling too close to the edges of the blocks, as this could weaken the wall. Be aware that cinder blocks can be brittle and prone to chipping or cracking.

2. Best Practices



Plan Carefully

Before drilling, carefully plan the route of the MC cable to avoid obstructions (pipes, other wiring, structural members).


Use the Right Tools

Use a masonry drill bit designed for drilling into concrete or block. Use a hammer drill for faster and easier drilling.

Drill Carefully

Drill slowly and steadily to avoid damaging the wall or the drill bit. Use a vacuum cleaner to remove dust as you drill.


Deburr the Hole

After drilling, deburr the edges of the hole to prevent the MC cable from being damaged.

Strain Relief

Make sure the MC connector provides adequate strain relief to prevent the cable from being pulled out of the box.


Consider an Old Work Box (if necessary)

If you are retrofitting a wall and don't have access to the back side, consider using an "old work" or "remodel" box, which has clamps that grip the wall from the inside. However, be aware that old work boxes might not be suitable for heavy devices or situations where robust support is needed. Running MC from the rear is typically easier with a standard box if you can access the back.

Check with your Local Inspector

Always* consult with your local electrical inspector to confirm that your wiring methods meet local codes and requirements. They can provide specific guidance for your situation.

In Summary:


Drilling into a cinder block wall for electrical wiring is often done, but requires careful attention to code compliance and best practices. Ensuring proper support, securing, grounding, and box fill are all crucial. Consult with a qualified electrician if you are unsure about any aspect of the work. The key to doing this safely and correctly is proper planning, using the correct materials, and following the applicable electrical codes. Flag for review

Previous Question Next Question