Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Exhaust hood

User: kec, Location: CT

Asked on: Sunday, November 2, 2025 at 9:26 am EST
Answered on: Sunday, November 2, 2025 at 9:26 am EST

Question: Doing a remodel on a kitchen and the designer had delivered a new Exhaust hood. This hood is replacing an existing hood with a remote fan.Looking at the wiring diagram and the entrance junction box this is what they provide. A handy box with terminal block and 18 awg wire to power uplights and red switch leg to remote fan. Called the manufactures tech Rep and asked why such small wire and his reply was this is how we do it all thetime and have not any problems with it.What is it I'm missing.

You're right to question this. It does seem potentially problematic, especially if you're replacing a hood with a more powerful remote fan. Here's a breakdown of what you might be missing and why you're right to be concerned

The Core Issue: Wire Gauge and Amperage
18 AWG: Limited Capacity

18 AWG wire is
very thin. According to the National Electrical Code (NEC) in the USA, it's only rated to carry a very small amount of current, typically around 5 to 7 amps. The exact amperage depends on the insulation type and installation conditions.

Remote Fan Load

Remote fans, especially those that are powerful enough to adequately vent a kitchen, can draw more current than 18 AWG is designed to handle safely. The amperage draw depends on the motor's horsepower and voltage, but a typical kitchen exhaust fan could easily draw several amps.

Safety Concerns

Overloading a wire causes it to overheat. Overheating can melt insulation, create short circuits, start fires, and damage the fan motor.

Why the Manufacturer Might Be Saying That (And Why It's Still Concerning)



They're Assuming Low Amperage Draw

The manufacturer might be making the assumption that the remote fan they're designing for is extremely low-power. Perhaps they're using a very efficient, small DC motor. However, that's still a gamble.

Minimum Requirements Compliance

They might be narrowly complying with the bare minimum electrical codes, hoping that the load will never exceed the wiring. The fact that they haven't encountered problems yet doesn't make it safe. It could just mean the system is barely working, or the previous installations were undersized.


Cost Savings

Using thinner wire saves the manufacturer money. It's a bottom-line decision.

Misunderstanding

The tech rep may not have a complete understanding of your situation (i.e., you are using an existing remote fan) or may be repeating something that is not in fact true.

What You Need To Do (And Considerations)


Find the Fan's Amperage (Current Draw)

The
most crucial thing is to find the

exact amperage rating (or wattage and voltage)
of the remote fan you'll be using. This is usually found on a label on the fan motor itself, or in the fan's documentation.2. Calculate Ampere Draw and Voltage Drop

Voltage drop refers to the decrease in voltage along a conductor. An adequately sized wire minimizes voltage drop. Voltage drop is a particular problem with long wire runs. The wire gauge has to increase as wire length increases to maintain consistent performance from the device.3.

Calculate the Wire Run

Find out how long the wire run is from the hood's handy box to the remote fan's location.4.

Check the NEC (National Electrical Code) or Local Electrical Codes

The NEC (or your local equivalent) has tables that specify the allowable ampacity (current-carrying capacity) of different wire gauges based on their insulation type, installation method, and ambient temperature.5.

Consult with a Qualified Electrician

This is the
most important step. An electrician can properly assess the situation, determine the correct wire gauge, and ensure that the wiring is safe and compliant with all applicable codes. They can also take into account factors like the length of the wire run, the type of insulation, and the installation environment. An electrician can run a new circuit with a sufficient amperage rating and wire gauge as needed.

Recommendations and Precautions



Do NOT rely solely on the manufacturer's wiring if you have any doubts.
Your safety is the priority. Larger Gauge is Almost Always Better (Within Reason)

Err on the side of using a larger wire gauge than you think you need. It provides a safety margin and can help prevent voltage drop, especially over longer wire runs.


Consider a Dedicated Circuit

If the remote fan is a high-power unit, it might be best to install a dedicated 15-amp or 20-amp circuit specifically for the fan. This ensures that the fan has adequate power and won't overload other circuits.*

If Possible Replace the Wire in the Handy Box

A handy box is designed to accept larger wire. You may need to remove the terminal block and add wire connectors.

In Summary:


The manufacturer's use of 18 AWG wire for the remote fan connection raises serious questions about safety and proper operation. Do not proceed without a thorough assessment by a qualified electrician. Prioritize safety and code compliance. It's better to be safe than sorry, especially when dealing with electrical wiring. Flag for review

Previous Question Next Question