User: Captorofsin1, Location: Florida
Asked on: Sunday, November 2, 2025 at 10:09 am EST
Answered on: Sunday, November 2, 2025 at 10:09 am EST
Question: Hello everyone. Just need a "sounding board".Qo panel.Yesterday I was at a call. Any load on the circuit would trip the combination art fault breaker (just want to make it clear that it's not an old school AFCI).Any receptacle I plug a lamp into and turn the lamp on it would flash and then the breaker wood trip. Same thing with the ceiling fans and the light kit on the ceiling fan. Turn on for split second and then break her trip.Tried swapping out to a new breaker. Same scenario.Reinstalled CAFCI breaker. Then I got the right idea of removing just the neutral (leaving hot and pigtail connected). Even with the load neutral disconnected off the arc fall breaker it would trip as soon as I turned on any lamp plugged into any receptacal on the circuit. I would flip the wall switches (ceiling fan would light kit) and same thing (motor would turn briefly and/or light would flash briefly and then arc fault breaker would trip).*This was only when there was a load. If I had the ceiling fan (light or motor) turned off (pull strings) and turned wall switches to "on" position, it would hold. I could plug a lamp into any receptacle and as soon as I turned on lamp, breaker wood trip.That small flash of light tells me that the circuit is finding a path back home somewhere else*JUST TO REITERATE, THIS IS WITH THE LOAD NEUTRAL DISCONNECTED FROM THE ART FALL BREAKER*The house appeared (as per what I saw in the panel, new receptacles, in the wiring going to the receptacle) to have been rewired in the last 10(?) years. In my professional opinion, the rewire was done by an electrical contractor. This tells me that (more than likely, but you never know ) that know neutrals were crossed anywhere. My intuition's telling me that more than likely somebody got overzealous with the staples when they were stapling the Romex and caused a break in the neutral (inside the jacket)... Fill in the blanks...Opinions?
Okay, let's break this down. You've done some good troubleshooting, and your instincts are probably leading you in the right direction. Here's a summary and some additional thoughts
Summary of the Situation:
Problem
Combination AFCI breaker trips immediately when any load is applied to the circuit (lamp, ceiling fan motor/light).
Breaker Type
Combination AFCI (CAFCI) - detects both arc faults and ground faults.
Troubleshooting Done
Replaced breaker with a new one - same issue. Disconnected the neutral of the circuit from the AFCI breaker - still trips with a load. This is the key observation.
Wiring
Appears relatively new and professionally installed, suggesting less likelihood of simple crossed neutrals.
Analysis and Opinions
Your observation that the breaker still trips when the neutral is disconnected is the most critical piece of information. This eliminates the possibility of a neutral-ground fault on that specific circuit as the direct cause. Here's why:1.
AFCI Breaker Function
AFCI breakers are designed to detect anomalies in the current waveform that indicate arcing. They also detect ground faults. When you disconnect the neutral, you've essentially isolated the return path for the circuit. If the problem were solely a neutral-ground fault ON THAT CIRCUIT, the breaker shouldn't trip when the neutral is disconnected (since no current can return through the neutral). The fact that it still trips indicates that the problem is likely elsewhere.2.
Phantom Voltage/Current
The brief flash of light is a clue that there is a complete circuit being made momentarily. Even with the neutral disconnected, there is an alternative return path being found.3.
Staple Theory
A damaged conductor inside the Romex jacket is plausible, but it would have to be the
hot wire. If you damaged the neutral that wouldn't cause the breaker to trip with the load neutral removed.
Possible Causes and Next Steps
Here's a more comprehensive list of potential culprits, ordered from most to least likely based on your troubleshooting:1.
Hot-to-Ground Fault
This is the most likely scenario, especially given the fact that the breaker trips even with the neutral disconnected. This means that when the load is turned on there is an almost immediate fault to ground.2.
Shared Neutral (Multi-Wire Branch Circuit Problem)
This is less likely if the house was recently rewired by a professional, but it's worth investigating. A multi-wire branch circuit (MWBC) shares a neutral between two hots. If the neutrals are improperly connected at the receptacle or in the panel, and a load is placed on another circuit sharing that neutral, it could create an imbalance and cause the AFCI to trip. To diagnose this, you'd need to check voltage between the hot conductors and the neutral. If you're getting a higher than expected voltage (e.g., significantly over 120V) on one of the circuits, it could indicate a shared neutral problem.3.
"Bootleg" Ground
It's possible that someone previously wired a receptacle incorrectly, using the neutral conductor as a ground. This can create a parallel path for current and confuse the AFCI. Check the wiring at receptacles carefully, especially looking for instances where the neutral is connected to the ground screw.4.
Faulty Appliance/Device
Even though multiple devices trigger the trip, it's worth absolutely confirming that none of the devices you're testing with have internal faults. Try a different lamp known to be good, and ideally test with a non-electronic load like a simple resistive heater (carefully, for a short time).5.
Neutral Backfeed
This is a less likely, but possible scenario. This would require a neutral from an unrelated circuit back-feeding into the disconnected neutral of the problem circuit.6.
Problem with the Panel Itself (Unlikely)
Very rarely, there could be an internal problem within the panel (loose connection, damaged bus bar). This is unlikely but could potentially cause erratic behavior.
Recommended Troubleshooting Steps (in order)
Visual Inspection
Thoroughly inspect the wiring at every receptacle, switch, and light fixture on the circuit. Look for: Loose connections. Nicked or damaged wires (especially where staples were used). Evidence of overheating. Improper wiring (neutral used as a ground).2.
Insulation Resistance Testing (Megger/Megohmmeter)
This is the most reliable way to find a ground fault. Use a megger to test the insulation resistance between: Hot to ground (with the neutral disconnected). Neutral to ground (with the hot disconnected).A low resistance reading (less than a few megohms) indicates an insulation breakdown and a likely ground fault. Start by disconnecting all loads (receptacles, fixtures) and testing from the panel. Then, if you find a fault, systematically reconnect sections of the circuit until the fault reappears, narrowing down the location.3.
Voltage Testing
With the circuit breaker ON (carefully!), use a multimeter to measure voltage: Between hot and neutral (should be approximately 120V). Between hot and ground (should be approximately 120V). Between neutral and ground (should be very close to 0V). A significant voltage reading between neutral and ground indicates a potential problem.4.
Continuity Testing
With the circuit breaker OFF and LOCKED OUT, use a multimeter to check for continuity: Between neutral and ground (should be no continuity except at the service entrance).5.
Load Isolation
Systematically disconnect sections of the circuit to isolate the problem. For example: Disconnect the wiring at each receptacle and light fixture, one at a time, and retest the circuit. This will help you pinpoint the section of wiring where the fault lies.6.
Check the Panel Neutral/Ground Bonding
Ensure that the neutral and ground are properly bonded in the main panel (usually a green bonding screw). An improper bond can cause neutral currents to flow on the ground wire.7.
Consult with an Experienced Electrician
If you're unable to find the problem after performing these steps, it's best to call in an experienced electrician who is familiar with AFCI breakers and troubleshooting techniques.
Important Safety Notes
Always work with the circuit breaker OFF and LOCKED OUT whenever possible. Use proper personal protective equipment (PPE), including safety glasses and insulated gloves. If you are not comfortable working with electricity, hire a qualified electrician.* Double-check your work to ensure that all connections are secure and properly insulated.
Let me know if you have any other questions or want to delve deeper into any of these areas. Good luck! Flag for review