Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: LFNMC

User: nizak

Asked on: Sunday, November 2, 2025 at 10:41 am EST
Answered on: Sunday, November 2, 2025 at 10:42 am EST

Question: Any tips on making LFNMC ( Carflex) easier to work with when outside temps start dropping?I keep it in the truck with the heat on but usually it gets rigid pretty quickly once it’s outside.Thanks

You're right, LFNC (Liquidtight Flexible Nonmetallic Conduit, often referred to as Carflex) gets tough to work with in cold weather. Here's a breakdown of tips to help you manage it

1. Heat Management is Key
Pre-Heating is Best



Keep it Warm (Long Term)

Your current method of keeping it in the heated truck is good initially. However, consider a dedicated warm spot for the LFNC.

Consider a Heated Blanket or Wrap

Electric heated blankets (the kind used for warming pets) or pipe-warming wraps can be used to directly warm the coil. Be careful not to overheat and damage the material (follow manufacturer's instructions). Monitor the temperature – you don't want it melting or becoming brittle.


Job Site Warm-Up (Short Term)



Immersion in Warm Water

Submerging the end you're working with in a bucket of warm (not hot!) water for a few minutes is very effective. Dry it thoroughly before connecting.


Heat Gun (Use with Extreme Caution)

A heat gun is risky because it can easily melt or distort the LFNC. If you must use one, keep it on a low setting, move it constantly, and maintain a good distance (at least 12 inches). Focus on gentle warming, not direct heat. Test on a small, inconspicuous piece first.

Insulated Transport

If you need to carry the LFNC a distance across a cold job site, wrap it in an insulated blanket or pad.

2. Work Strategies
Cut to Length Inside

If possible, cut the LFNC to the desired length inside where it's warmer and more pliable. This makes the initial cut and handling much easier.

Bend Carefully

Cold LFNC is more likely to kink or crack when bent. Make slow, gradual bends. If it's really stiff, use a heat source to soften it before bending (as described above).


Use Proper Tools



Sharp Cutter

Use a sharp utility knife or specialized LFNC cutter for clean, precise cuts. Dull blades require more force and can crush the conduit.


Deburring Tool

After cutting, deburr the inside and outside edges of the LFNC to remove any sharp burrs that could damage wires or create a poor connection.

Work in Sections

Instead of trying to run an entire long length of stiff LFNC at once, break the task down into smaller, more manageable sections.

3. Material Considerations
Temperature Rating

Check the temperature rating of your LFNC. Some are rated for lower temperatures than others. If you regularly work in very cold conditions, consider using a more cold-resistant type. Look for types specifically designed for low-temperature applications.

Material Type

Different LFNC materials have slightly different flexibility characteristics. Experiment with different brands and types to see which performs best for you in cold weather.

4. Safety First
Gloves

Wear gloves to protect your hands from the cold and from sharp edges when cutting and handling the LFNC.

Eye Protection

Always wear safety glasses or goggles to protect your eyes from debris.


Electrical Safety

Ensure the power is off and properly locked out/tagged out before working with any electrical components.

Important Cautions



Avoid Overheating

Excessive heat can damage or distort the LFNC, making it brittle or causing it to lose its shape.


Never Use Open Flame

Never use an open flame (like a torch) to heat LFNC. This is extremely dangerous and could cause a fire or explosion.*

Follow Manufacturer's Instructions

Always refer to the LFNC manufacturer's instructions for proper installation and temperature guidelines.

In Summary:


The key to working with LFNC in cold weather is to keep it as warm as possible before and during installation, use appropriate tools and techniques, and prioritize safety. By taking these steps, you can significantly reduce the challenges of working with LFNC in cold conditions. Flag for review

Previous Question Next Question