Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Working with rigid

User: jared123, Location: Texas

Asked on: Sunday, November 2, 2025 at 1:29 pm EST
Answered on: Monday, November 3, 2025 at 1:14 am EST

Question: I am JIW with mainly commercial experience. Have bent/threaded rigid mainly for underground changovers so precision wasnt paramount.What technical advice do you have for working with rigid. Eg if i calculate the gain so i can predermine the length of rigid and thread it before bending do you assume it wont fully thread on and take that into account?Thanks

Okay, JIW with commercial experience transitioning to more precise rigid conduit work. Here's some technical advice focusing on pre-threading and accurate bending, with an emphasis on considerations for threading depth

Key Considerations Before Bending and Threading
Material Matters

Aluminum, galvanized steel, and stainless steel rigid behave differently. Aluminum is softer and more prone to crushing if you over-tighten fittings. Galvanized is standard, but stainless requires specific tools and lubricants.


Conduit Size

Smaller diameter conduit (e.g., 1/2", 3/4") is generally easier to bend accurately. Larger sizes (2", 3", 4") require more force, better benders, and more careful planning.

Bender Choice and Condition

Ensure your bender is properly sized for the conduit you're using. A worn or damaged bender will introduce inaccuracies. Hydraulic benders are more precise and consistent than hand benders, especially for larger sizes. Use the correct shoes/formers.


Temperature

Cold weather can make rigid more brittle and harder to bend. Consider warming the conduit slightly (indirectly, never with direct flame) in very cold conditions.

Pre-Threading and Length Calculations (The Core of Your Question)


This is where precision is key. You want to accurately predict the final length after bending and threading.1. Precise Measurements



Take Accurate "Before" Measurements

Before you cut and thread,
double-check your measurements. Even small errors accumulate.

Account for Coupling/Fitting Depths

Know exactly how far the conduit will thread into each fitting you plan to use (couplings, connectors, LB's, etc.). Refer to manufacturer specs or measure a fitting directly with calipers for the most accurate data. Different manufacturers can have slightly different thread depths.2.

Gain Calculation



Understand Bender Gain

Each bender has a specific gain (or take-up) that represents the length of conduit
consumed by the bend. This value is usually printed on the bender shoe or in the bender's documentation.

Gain Varies with Bend Angle

The gain is dependent on the bend angle. A 90-degree bend will have a different gain than a 30-degree bend. Use the bender manufacturer's chart or online calculators to determine the correct gain for your specific bend angle.

Multiple Bends

When dealing with multiple bends in a single piece of conduit, calculate the gain for each bend
individually and sum them.3.

Shrinkage Calculation



Understand Bender Shrinkage

Each bender has a specific shrinkage that represents the length of conduit taken off by the bend. This value is usually printed on the bender shoe or in the bender's documentation.

Shrinkage Varies with Bend Angle

The shrinkage is
dependent on the bend angle. A 90-degree bend will have a different shrinkage than a 30-degree bend. Use the bender manufacturer's chart or online calculators to determine the correct shrinkage for your specific bend angle.

Multiple Bends

When dealing with multiple bends in a single piece of conduit, calculate the shrinkage for each bend individually and sum them.4.

Threading Allowance (Crucial!)



Yes, Account for Less-Than-Full Thread Engagement

You are correct to consider that the conduit may not thread in
fully to the coupling or fitting. This is especially true with galvanized rigid due to coating thickness variations.

How Much to Account For?
This is the tricky part. There is no "one size fits all" answer. Here's a breakdown: Manufacturer Specs (Best Case)

Ideally, get the manufacturer's spec for the minimum thread engagement they recommend for their fittings. This is the
safest approach.

Rule of Thumb (More Conservative)

A common rule of thumb is to assume you'll lose about 1-2 threads worth of length per connection. Measure the thread pitch of your conduit (distance between thread crests). Multiply the thread pitch by the number of threads you expect to lose. This gives you an estimated length to add to your initial conduit length before threading.

Test Threading

The best method is to take a short piece of scrap conduit, thread it, and test how far it threads into the actual fittings you'll be using. Measure the remaining exposed threads on the conduit. This is the most accurate way to determine the threading allowance for your specific materials.5.

The Formula

Final Cut Length = (Required Straight Run Length) + (Total Gain) - (Total Shrinkage) + (Threading Allowance)


Required Straight Run Length

The physical distance you need to cover between connection points after bends.

Total Gain

Sum of the gain for all bends.


Total Shrinkage

Sum of the shrinkage for all bends.

Threading Allowance

Sum of the threading allowance for each end you'll be threading. Multiply your single-end allowance by 2 if you're threading both ends.

Threading Techniques
Use the Right Die

Ensure your threading die is the correct size and type for the conduit (NPT standard). Dull or damaged dies will create poor threads.

Sharp Dies

Sharp dies are
crucial. Get them sharpened regularly or replaced when they start producing rough threads.

Proper Lubrication

Use a high-quality cutting oil specifically designed for threading steel or aluminum. Adequate lubrication prevents galling, reduces friction, and produces cleaner threads. Apply liberally during the entire threading process.

Consistent Pressure

Apply even pressure when threading. Avoid forcing the die, as this can damage the threads or the conduit.


Clean Threads

After threading, thoroughly clean the threads with a wire brush to remove any metal shavings or debris.

Check Thread Quality

Visually inspect the threads for sharpness, completeness, and any signs of damage. Use a thread gauge if you need to verify the thread profile.

Bending Techniques
Proper Support

Support the conduit properly during bending to prevent it from kinking or collapsing.

Smooth, Controlled Bends

Make bends smoothly and gradually. Avoid jerking or applying excessive force.


Avoid Overbending

Be careful not to overbend, as it's difficult to correct. If you do slightly overbend, try to correct it gradually.

Consistent Bending

For multiple identical bends, use a bending table or jigs to ensure consistency.


Angle Finder/Protractor

Use a digital angle finder or protractor to verify bend angles accurately.

Bending Grease

Use bending grease in the bender shoe.

Troubleshooting
Coupling Won't Tighten



Cross-Threading

Make sure you're not cross-threading the fitting. Back it off and start again carefully.


Thread Damage

Inspect the threads on both the conduit and the fitting for damage. Replace the damaged component.

Thread Obstruction

Check for debris or burrs in the threads. Clean them out with a wire brush or thread chaser.


Coating Buildup

If using galvanized conduit, the zinc coating can sometimes interfere with threading. A thread chaser or a slightly deeper thread can help.

Bend is Off



Re-Evaluate Measurements

Double-check all your measurements and calculations.

Bender Error

Calibrate your bender regularly.


Adjust in Small Increments

If the bend is slightly off, make small adjustments to correct it.

Tips for Success
Practice on Scrap

Always practice your bends and threading on scrap conduit before working on the final piece.


Document Your Process

Keep a record of your measurements, calculations, and techniques. This will help you improve your accuracy over time.

Double-Check Everything

Before you cut, bend, or thread, double-check all your measurements and calculations.


Be Patient

Accurate rigid conduit work takes time and patience. Don't rush the process.

Ask for Help

If you're unsure about something, don't hesitate to ask a more experienced electrician for help.


Invest in Good Tools

High-quality benders, threaders, and measuring tools will make your job easier and more accurate.

Consider a Laser Level

For long runs or complex bends, a laser level can help you maintain accuracy and alignment.


Use a Thread Gauge:
A thread gauge is an invaluable tool for verifying the thread pitch and profile of your conduit.By carefully considering these factors and practicing good techniques, you can significantly improve your accuracy when working with rigid conduit and avoid costly mistakes. Good luck! Flag for review

Previous Question Next Question