Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Solar routed through sub panel?

User: whackit, Location: Los Angeles, CA

Asked on: Tuesday, November 4, 2025 at 12:26 pm EST
Answered on: Tuesday, November 4, 2025 at 12:26 pm EST

Question: I inherited a job that was prepped for solar but they did one thing I'm not sure about. Solar panels are located on an outbuilding that has a sub panel - the MSP and solar equipment is all located on the main building. For some reason they chose to route the solar (AC) conduit to the sub panel and then another conduit for solar exits through the bottom interior of the sub panel essentially just using the subpanel as a j box. Redoing this is a bit of a nightmare -the conduit exiting the sub panel is in concrete and then exits under a slab to a trench. Is it acceptable to just route the solar circuit through the sub panel? Wire will be straight through. No splices etc and of course properly identified.

Okay, let's break down the code implications and potential solutions. It sounds like you're asking if using the subpanel enclosure as a kind of "pass-through" junction box is permissible for the solar AC circuit.

Here's a breakdown of why this might be problematic and what to consider



Code Considerations (Likely NEC)



110.12 Mechanical Execution of Work

NEC requires neat and workmanlike manner in electrical installations. The use of the subpanel as a pass-through for unrelated conductors might be construed as not meeting this requirement if it clutters the enclosure excessively.

312.8 Switch and Overcurrent Device Enclosures

This section is critical. It addresses the use of enclosures for things other than their intended purpose (terminating conductors on the bus, switch, or breaker). While 312.8 allows conductors to pass
through an enclosure, there are very important restrictions:

(A) Wiring System(s) with a Lower Voltage

Conductors of circuits rated 1000 volts, nominal, or less, may pass through an enclosure if all of the following conditions are met:(1) The conductors are within a complete raceway or cable assembly that is identified for the purpose(2) The raceway or cable assembly fills no more than 75 percent of the cross-sectional area of the enclosure(3) The raceway or cable assembly is securely fastened to the enclosure(4) The raceway or cable assembly is installed so the conductors are not subject to physical damage

Clear Working Space

The passing conductors
cannot impede the operation of the breakers in the panel or take up so much space as to prevent proper cooling.

Proper Marking

The solar AC conductors would need to be properly marked and identified, especially if they are of different voltage.

690.4(J) Wiring Methods. (AC Modules)

Wiring methods must comply with Chapter 3 and Parts I and II of Article 690.


690.31(G) Identification and Grouping.
You mentioned identification. It's very important. Practical Considerations



Enclosure Fill

Adding another conduit and the conductors inside it will further crowd the subpanel. This can make future troubleshooting and maintenance difficult. It also affects heat dissipation within the panel.

Safety

Crowded enclosures are inherently more dangerous because of the increased risk of accidental contact.


Future Expansion

Using the subpanel as a pass-through limits future expansion or modifications to the system.

Inspection

An inspector
could reject the installation if they feel it's not neat, workmanlike, and compliant with the code.

Is it
Acceptable? Maybe, but it's borderline and depends on the details



Here's what needs to be absolutely true to make it potentially acceptable (consult the NEC and a licensed electrician for definitive advice)


Raceway

The solar AC circuit
must be within a complete and properly secured raceway inside the subpanel enclosure (e.g., EMT conduit). You said conduit, so that's good.2.

Fill Rate

The cross-sectional area of the conduit
must not exceed 75% of the enclosure's cross-sectional area. Calculate this carefully.3.

Clearance/Access

The conduit cannot obstruct access to breakers or other components in the subpanel.4.

Identification

The solar AC conductors
must be clearly and permanently identified as "Solar AC Circuit" (or similar). Use appropriately colored tape or labels.5.

Workmanship

The installation must be neat, professional, and not appear haphazard.6.

Mechanical Protection

The raceway must be securely fastened and protected from physical damage.

Alternatives to Consider (Even Though You Said They're a Nightmare)



External Junction Box

This is the cleanest and preferred solution. Dig up a little more concrete outside the subpanel, install an appropriately sized and rated weatherproof junction box, make the connections within the junction box, and properly seal all conduit entries. This keeps the subpanel enclosure solely for its intended purpose. It's generally the most code-compliant and maintainable option.

Larger Subpanel

If you
must use the subpanel as a pass-through and it's very tight, consider replacing it with a physically larger subpanel to provide more room and meet the fill requirements. This is still a significant undertaking.

Consult with an Electrical Engineer or Master Electrician

The best course of action is to have a qualified professional review the specific installation and provide guidance based on local codes and best practices. They can assess the existing conditions and recommend the most cost-effective and compliant solution.

In Summary

While technically possible to use the subpanel enclosure as a pass-through for the solar AC circuit, it's not ideal and requires very careful attention to detail. It's almost always better to use an external junction box or a larger subpanel. Weigh the cost of doing it "right" against the potential for inspection failure, safety issues, and future problems. If the existing set up doesn't meet the requirements, it needs to be changed.

Disclaimer:
I am an AI chatbot and cannot provide electrical advice. This information is for general guidance only. Always consult with a qualified and licensed electrician for any electrical work. Flag for review

Previous Question Next Question