Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Water pipe connection

User: OK Sparky 93, Location: Iridea14Strat

Asked on: Wednesday, November 5, 2025 at 11:34 am EST
Answered on: Wednesday, November 5, 2025 at 11:34 am EST

Question: if a water pipe is used as an electrode, would it also be required to fall under the bonding code requirements. This I don’t know if I am thoroughly clear on. If it was co formed that a GEC did go to the entry point of water pipe, would it be that you would only make a jumper to the hot side of a water heater, provided if everything was copper throughout?

Okay, let's break down the grounding and bonding requirements related to water pipes used as electrodes.

Water Pipe as a Grounding Electrode Permitted Use

Yes, a metal underground water pipe is a permitted grounding electrode if it meets specific requirements outlined in the NEC (National Electrical Code). NEC 250.52(A)(1) is the relevant section.


Requirements to be a Grounding Electrode



Metallic

The water pipe must be metallic.


Direct Contact with Earth

It must be in direct contact with the earth for at least 10 feet (3.0 m), including any metal well casing bonded to the piping.

Continuity

It must be electrically continuous to the point of connection to the grounding electrode conductor (GEC).


No Insulating Sections

There cannot be any insulating sections or joints that interrupt the electrical conductivity of the pipe within the 10-foot earth contact length.

Bonding Requirements (When a Water Pipe is Used as an Electrode)


Yes, if you are using a metal water pipe as a grounding electrode, it must be bonded. The bonding requirements are critical for safety. Supplemented by Another Electrode

The water pipe
must be supplemented by an additional grounding electrode. This could be a ground rod, ground ring, concrete-encased electrode (ufer), or other approved electrode (NEC 250.53(D)(2)). This is important because water pipes can be subject to corrosion and become unreliable grounding paths.

Bonding Jumper

A bonding jumper is required around any insulated couplings or sections that are likely to be removed or replaced. The bonding jumper ensures the water pipe's continuity is maintained as an equipment grounding conductor in case of a fault (NEC 250.104(A)(1)).

Regarding the Grounding Electrode Conductor (GEC) and Water Heater


Here's where clarity is essential:1. GEC to the Water Pipe

You are correct that a GEC (Grounding Electrode Conductor) needs to connect to the water pipe (NEC 250.68(C)(1)). This connection should be made within 5 feet of where the water pipe enters the building.
2.


Bonding Jumper to the Water Heater

Here's where the distinction between grounding and bonding comes into play. If you have a metal water piping system, you need to bond all metal water piping to the electrical system (NEC 250.104(A)).

Purpose of Bonding

Bonding is to ensure that all metal parts that could become energized due to a fault are at the same electrical potential, minimizing the risk of electric shock.


The bonding jumper to the water heater is required regardless of whether the piping is continuous copper or not, unless specific conditions are met.
These conditions are in NEC 250.104(A) A bonding jumper from the service equipment to the water heater is typically run from the main electrical panel to the metallic water piping within 5 ft of the water heater. This establishes an effective ground-fault current path from the water heater back to the electrical panel. Sizing

Refer to NEC Table 250.102(C)(1) to correctly size the bonding jumper based on the size of the service conductors.

So to summarize bonding to the water heater, you would bond to the cold water side of the water heater. This is done regardless of copper piping, you are not bonding to the hot water side of the water heater!
Key Considerations and Cautions Local Codes

Always check and comply with local electrical codes, which may have stricter requirements than the NEC.


Licensed Electrician

All grounding and bonding work should be performed by a qualified and licensed electrician to ensure it is done safely and correctly. Incorrect grounding and bonding can create serious safety hazards.

Inspection

Have your grounding and bonding system inspected by the appropriate authorities to verify compliance.


Corrosion

Pay close attention to potential corrosion points on the water pipe, as this can compromise the effectiveness of the grounding electrode. Consider using corrosion-resistant clamps and conductors.*

Water Meter Jumpers
: Jumpers are often found on water meters so you should check for those, if there are you must ensure the jumper is adequate and installed correctly.

In summary: Using a water pipe as a grounding electrode is permitted under certain conditions but requires bonding to other metal piping systems. Bonding is crucial for creating a safe electrical system by equalizing potential and providing a path for fault current to return to the source. Always consult the NEC and local codes and hire a qualified electrician for any grounding and bonding work. Flag for review

Previous Question Next Question