Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Are seals required in this situation?

User: TwoBlocked, Location: Bradford County, PA

Asked on: Thursday, November 6, 2025 at 6:09 pm EST
Answered on: Thursday, November 6, 2025 at 6:16 pm EST

Question: Am working up a quote for indoor and exterior lighting on a gas compressor building. The inside of the building is Class I Div 2. The outside is unclassified. Both the indoor and outdoor lights are Class I Div 2, not requiring a seal at their entries. I'd like to run rigid conduit on the inside of the building with tees going to both the inside and the outside lights with Liquatite. I am not sure if I can do so without a seal on the portion of the conduit going through the wall going to the outside lights.Reading the exemptions, I think I am not required to have seals if I tee off going through the wall with rigid, or if I transition to cable, but not if I use Liquatite?What do you fine folks say?

Okay, let's break down the NEC requirements for seals in Class I, Division 2 locations, particularly focusing on your specific scenario.

Understanding the Core Principles

The main purpose of seals in hazardous locations is to prevent the propagation of an explosion from inside the conduit system to the surrounding atmosphere or vice versa. This is especially critical in Class I locations where flammable gases or vapors are present.

NEC Relevant Sections to Consider NEC 501.15(B)(1)

This is your main rule for seals in Division 2 locations. It generally requires seals where conduits leave a Class I, Division 2 location. However, there are specific exceptions.


NEC 501.15(B)(2) Exception

This is the key to your question. It provides exceptions to the seal requirement if specific conditions are met.

NEC 501.15(B)(1) Exception 1
This states the seal shall not be required where a raceway leaves a Class 1, Division 2 location if the length of the raceway does not exceed 10 feet and the raceway is sealed where it enters an enclosure which is required to be approved for the Class 1, Division 2 location.

Analyzing Your Scenario

Here's how the NEC applies to your proposed design:1. Indoor (Class I, Division 2)

You are running rigid conduit within the Class I, Division 2 area. This is generally acceptable. The Class I, Div 2 light fixtures inside the building do not require seals at their entries. This is also acceptable, assuming these fixtures are listed for Class I, Div 2 and meet the specific requirements for unsealed connections (usually small enclosure volume and no arcing devices).2.

Wall Penetration and Transition to Outside (Unclassified)

This is the critical area.


Rigid Conduit to Tee

If you have a rigid conduit tee inside the Class I, Division 2 area, with one branch continuing in rigid conduit a short distance to the exterior wall and then transitioning to Liquatite to the outdoor (unclassified) light, you need to carefully consider the exception to 501.15(B)(1).

Liquatite (Flexible Metal Conduit) Through the Wall

This is where the potential problem lies. While Liquatite itself is permitted in Class I, Division 2 under specific conditions, its
use as the sole raceway transitioning through the wall directly to the unclassified area may not be covered by the exceptions to 501.15(B)(1).

Why Liquatite Alone Might Be Problematic


The core issue is that the exceptions to 501.15(B)(1) often rely on the
inherent properties of the raceway. Rigid conduit, when properly installed with threaded connections, provides a tight, robust path. The exceptions often consider rigid conduit as sufficiently restricting the passage of gases/vapors under certain conditions (length limits, sealed enclosures).Liquatite, while listed for hazardous locations, is flexible and its fittings are not generally considered as providing the same level of gas/vapor restriction as a properly made-up rigid conduit system.

Possible Solutions (Assuming No Seal Requirement Desired)


Transition to Cable Inside the Building

If you transition
inside the Class I, Division 2 area to a cable that is suitable for hazardous locations and is also suitable for wet locations (since it's going outside), you might be able to avoid a seal. The cable must meet the requirements of 501.10(B)(1)(a)(3). Consider using TC-ER-HL cable. The key is that the cable must be permitted to be run through the wall.
2.


Minimize Conduit Length and Seal at Fixture

Run rigid conduit as short as possible from the tee to the exterior light fixture, and seal the conduit at the light fixture. This may require using a special sealing fitting approved for this purpose. Be careful that the fixture can handle the weight and stress.3.

Consider a Sealing Fitting at the Wall

Install a sealing fitting right where the rigid conduit exits the wall. This is a straightforward solution and ensures compliance.

The Strongest Recommendation

To be absolutely certain of compliance,
consult with your local Authority Having Jurisdiction (AHJ). They have the final say on interpretations of the NEC in your specific location. Present your proposed design to them, clearly outlining your understanding of the NEC and the exceptions you believe apply.

In summary, using Liquatite as the sole raceway transitioning through the wall from Class I, Division 2 to an unclassified area is a likely violation of NEC 501.15(B)(1) without a seal. You'll need to either use a sealing fitting, transition to a cable suitable for hazardous locations and wet locations
inside* the building, seal at the fixture, or obtain approval from your local AHJ for your specific installation.
Flag for review

Previous Question Next Question