Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Sizing Neutral

User: augie47, Location: Tennessee

Asked on: Friday, November 7, 2025 at 1:34 pm EST
Answered on: Friday, November 7, 2025 at 1:35 pm EST

Question: When I wore a younger mans clothes and did this every day this question was child's play but old brains don't work as well as younger ones400 amp 240/120 single phase service commercial building.No load calculations have been made.Service conductors will be parallel in one conduit.220.61 allows the neutral to be sized at 200 amps + 70% of 200 amps or 340 amps,Neutral is not considered to be current carrying (unbalanced load) so no fill adjustment required for neutral.Question:Since the neutral does not terminate on a device using 90deg conductors can the neutral be reduced to 3/0AL (175 X 2) or is it required to comply with the 75deg rating ?

Okay, let's break down this problem, focusing on the NEC requirements and addressing your specific question.

Understanding the Situation 400A, 240/120V Single Phase Service

This is a common setup for smaller commercial buildings.


Parallel Conductors

Using multiple conductors per phase to handle the 400A.

No Load Calculations

This is a critical omission. While we can size the neutral based on the 220.61 method, ideally, you'd perform a full load calculation. This would give you a more accurate (and potentially smaller) neutral size.


220.61 (Neutral Load)

You've correctly identified the calculation method: 200A + 70% of (Remaining Load up to 200A). In this case, that's 200A + (0.70 200A) = 340A.

Neutral Not Considered Current-Carrying

Correct assumption. In single-phase residential/commercial services, the neutral is considered a grounded conductor, not a current-carrying conductor for the purpose of fill adjustments.

The Core Question: Ampacity and Termination Temperatures
You're asking if you can use a smaller aluminum conductor (3/0 AL) for the neutral, considering: It's rated at 175A at 75°C. (So, two 3/0 AL conductors would provide 350A of ampacity) You have a calculated neutral load of 340A. The neutral doesn't terminate on a device requiring 90°C conductors.

NEC Analysis and Answer

The answer is NO, you cannot reduce the neutral conductors to 3/0 AL and terminate at 75 deg. Here's why:1. NEC 110.14(C): Termination Temperature Limitations. This is the KEY article. It states: "(C)(1) Equipment Provisions. The ampacity of conductors with insulation rated for 75°C (167°F) or 90°C (194°F) shall be permitted to be used, provided one or more of the following conditions apply:(1) The equipment is listed and marked for use with 75°C (167°F) rated conductors.(2) The equipment is listed and marked for use with 90°C (194°F) rated conductors, and the conductors are terminated within the equipment in accordance with the equipment's listing.(3) The equipment is designed and marked for use with 75°C (167°F) rated conductors.(4) The equipment is designed and marked for use with 90°C (194°F) rated conductors, and the conductors are terminated within the equipment in accordance with the equipment's design."In short, the weakest link in the system dictates the temperature rating you use for ampacity calculations. Unless you have equipment specifically listed for 90°C termination on the neutral, you must use the 75°C ampacity rating.2. Ampacity Must Exceed Calculated Load

Regardless of the termination temperature, the
ampacity of the conductor must be equal to or greater than the calculated load. Your calculated neutral load is 340A.3.

Parallel Conductors and Ampacity

Since you're paralleling conductors, the combined ampacity of the parallel conductors must meet or exceed the 340A requirement. Two 3/0 AL conductors at 75°C are rated 175 amps each, so two conductors have a total ampacity of 350 amps.4.

Practical Application

If your load is 340 amps and you are terminating at 75 deg then using (2) 3/0 is acceptable

Important Considerations
Load Calculations

I cannot stress enough the importance of performing a proper load calculation according to NEC Article 220. The 220.61 method is a permitted method, but it might not be the most accurate or economical method.

Local Amendments

Always check with your local electrical inspector for any amendments to the NEC that might apply in your jurisdiction.


Aluminum vs. Copper

Remember that aluminum conductors require proper termination techniques and anti-oxidant compounds to prevent corrosion.*

Safety

Always prioritize safety. If you are not 100% confident in your calculations or the correct application of the NEC, consult with a qualified electrical engineer or electrician.

In Summary


While the two parallel 3/0 AL conductors are rated for more than the 340 amp neutral load calculated based on NEC 220.61, the termination requirements of NEC 110.14(C) generally require that you size the conductors based on the lowest temperature rating of the equipment to which they are connected.A full load calculation is highly recommended. If the load turns out to be significantly lower, it might open up other options. Flag for review

Previous Question Next Question