Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: TC-ER-HL

User: kjroller, Location: Dawson Mn

Asked on: Monday, November 10, 2025 at 4:16 pm EST
Answered on: Monday, November 10, 2025 at 4:17 pm EST

Question: Is TC-ER-HL acceptable to run through cable tray in a class 1 div 1 area I believe it is or is it only available in a flexible cord situation?

Let's break down the situation and the code implications of using TC-ER-HL cable in a Class 1, Division 1 location.

Understanding the Key Components Class 1, Division 1 Location

This is a hazardous location where ignitable concentrations of flammable gases, vapors, or liquids
exist continuously, intermittently, or periodically under normal operating conditions. It's the most restrictive type of hazardous location.

TC-ER-HL Cable



TC

Tray Cable. Indicates it's designed for use in cable trays.


ER

Exposed Run. Means it's sunlight-resistant and can be run outside of a raceway (conduit) in many applications.

HL

Hazardous Locations. Specifically means it is listed and approved for use in Class I, Division 2 hazardous locations as well as Class II, Division 2 and Class III hazardous locations.

NEC Requirements for Class 1, Division 1 Locations


The National Electrical Code (NEC)
severely restricts wiring methods in Class 1, Division 1 locations. The basic principle is to use methods that prevent ignition of the hazardous atmosphere, even in the event of a fault.Here's the relevant section from the NEC: NEC 501.10 Wiring Methods (A) Class I, Division 1. All wiring and equipment in Class I, Division 1 locations shall be installed using one or more of the following wiring methods: (1) Threaded Rigid Metal Conduit (RMC) or Threaded Steel Intermediate Metal Conduit (IMC)

Must be explosionproof.

(2) Type MI Cable

Mineral-insulated, metal-sheathed cable, terminated with approved fittings.


(3) Explosionproof Equipment

Equipment specifically listed for Class I, Division 1.

(4) Intrinsically Safe Systems

Associated wiring for intrinsically safe systems, installed per Article 504.


(5) Optical Fiber Cable

Where permitted in 501.16.

(6) Special Permission

The authority having jurisdiction (AHJ)
may grant permission for other wiring methods if those methods can be demonstrated to maintain area classification and provide personnel protection equivalent to the methods listed above.

This is very rare and requires substantial engineering justification.
Analysis and Conclusion

Based on the NEC, TC-ER-HL cable is NOT generally permitted as a wiring method in a Class 1, Division 1 location.

Here's why:1. It's Not Listed

TC-ER-HL is not one of the approved wiring methods explicitly listed in NEC 501.10(A).
2.


Hazardous Location Rating

While the "HL" designation means the cable is rated for hazardous locations, it's rated for Division
2, not Division 1. Division 2 is a much less restrictive environment. The "HL" rating on TC-ER-HL ensures that it does not become a source of ignition. Division 2 locations typically only require that a product isn't a source of ignition during an abnormal failure mode.3.

Explosionproof Requirements

Division 1 environments typically require explosion proof equipment to isolate the electrical components that have the potential for ignition. A TC-ER-HL cable isn't explosionproof.

Flexible Cords


The fact that you mentioned flexible cords might create confusion. While flexible cords are allowed in SOME hazardous locations, their use is
extremely limited and very specific. They are almost never permitted for general wiring in a Class 1, Division 1 location. Here's the basic rules for flexible cord use in hazardous locations: 501.14(B)(1) Class I, Division 1

Flexible cords can be used only for portable lamps or portable utilization equipment where specifically permitted elsewhere in the code. They must have suitable seals where they enter explosionproof enclosures.

501.14(B)(2) Class I, Division 2

Flexible cords can be used if they are (1) approved for hard usage, (2) contain an equipment grounding conductor, and (3) are terminated with a grounding-type attachment plug and receptacle.

Important Considerations
AHJ Authority

The Authority Having Jurisdiction (AHJ) has the final say on what is permitted. While the NEC provides the rules, the AHJ interprets and enforces them.

Engineering Justification

As mentioned above, NEC 501.10(A)(6) allows the AHJ to approve other methods if they are proven to provide an equivalent level of safety. This would require extensive engineering analysis and documentation. It's extremely unlikely this would be granted for TC-ER-HL in a Division 1 location.


Specific Applications

There might be very niche situations where a component within an approved system (e.g., an intrinsically safe system) uses a specialized cable that resembles TC-ER-HL. However, this would be part of a complete, listed system, not a general wiring method.

In summary: TC-ER-HL is NOT generally permitted for running through cable tray in a Class 1, Division 1 location.
You must use approved wiring methods like RMC or IMC with explosionproof fittings, or MI cable with approved fittings. Always consult with a qualified electrical engineer and the local AHJ for specific guidance on wiring in hazardous locations. This is a critical safety issue. Flag for review

Previous Question Next Question