Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: correct wiring for a residential 15kw heat strip

User: Bumpa, Location: Jacksonville, Florida

Asked on: Tuesday, November 11, 2025 at 11:44 am EST
Answered on: Tuesday, November 11, 2025 at 11:47 am EST

Question: I am connecting a 15kw heat strip for an air-conditioning unit. FLA 62.5, MCA 103.8a, MOCP 110a. Can I use a non-fuseable disconnect for the unit? I will use #4 copper thhn and an 80a 240v breaker at the panel.

Okay, let's break down the requirements and see if your proposed plan meets code.

Understanding the Terms



FLA (Full Load Amps)

The current the heat strip draws under normal operating conditions.


MCA (Minimum Circuit Ampacity)

The minimum size conductor you're allowed to use. This value is calculated to account for continuous operation and other factors.

MOCP (Maximum Overcurrent Protection)

The
maximum size breaker or fuses allowed to protect the circuit.

Your Proposal



Non-Fusible Disconnect

You're considering using a disconnect switch without fuses.

#4 AWG Copper THHN

This is your proposed wire size.


80A Breaker

This is your proposed breaker size at the panel.

Code Considerations (NEC - National Electrical Code)


Conductor Sizing (MCA)

Your MCA is 103.8A. You must use a conductor rated for at least this ampacity.

#4 AWG Copper THHN Ampacity

According to NEC Table 310.16 (assuming 75°C termination temperature, which is common), #4 AWG copper THHN is typically rated for 85 amps.

This is NOT sufficient for your MCA of 103.8A.
You would need to upsize your conductors to meet the MCA requirement. #2 AWG copper is typically rated for 95 Amps, which is still not sufficient. #1 AWG Copper is rated for 110 amps and would be the smallest allowed copper wire.2. Overcurrent Protection (MOCP)

Your MOCP is 110A. This is the maximum size breaker you can use. You CAN use a breaker smaller than the MOCP.

Your 80A Breaker

This is
less than the MOCP of 110A, so it could be acceptable if it also protects the conductors.3.

Disconnect Switch



Rating

The disconnect switch must have an ampere rating equal to or greater than 115% of the nameplate rated load. The disconnect must be rated to interrupt the load.

Non-Fusible vs. Fusible

Whether you use a fusible or non-fusible disconnect depends on whether you need additional overcurrent protection at the disconnect.


Non-Fusible is Permissible

You can use a non-fusible disconnect if the breaker at the panel provides adequate overcurrent protection for the equipment and the conductors. In your case, the breaker is smaller than the MOCP, so you can use a non-fusible disconnect, provided it's properly rated for the voltage and current.4.

Termination Temperature

Ensure your equipment (heat strip, breaker, and disconnect) are rated for the conductor temperature you're using (usually 75°C). Using the wrong temperature rating can lead to undersized conductors.

Revised Recommendation


Upsize Conductors

You MUST use #1 AWG copper THHN (rated 110 amps) to meet the MCA requirement.2.

80A Breaker

Continue with the 80A breaker at the panel.3.

Non-Fusible Disconnect

A properly rated non-fusible disconnect is acceptable because the breaker is less than the MOCP and protects the circuit. Ensure the disconnect is rated for at least 115% of the load.4.

Grounding

Make sure your grounding is correct. Consult NEC Article 250 for grounding requirements.

Important Notes



Local Codes

Always check with your local electrical codes and inspectors. They may have amendments to the NEC or additional requirements.

Qualified Electrician

This is electrical work involving significant current. It's highly recommended to have a qualified electrician perform the installation to ensure it's safe and code-compliant. Incorrect wiring can be dangerous and lead to fire or electrocution.*

Voltage Drop

Check the voltage drop for your run length. Excessive voltage drop can affect the performance of the heat strip.

Disclaimer:
I am an AI chatbot and cannot provide professional electrical advice. This information is for general guidance only. Consult with a qualified electrician for your specific installation. Flag for review

Previous Question Next Question