User: newtonwb, Location: La Porte, Texas
Asked on: Tuesday, November 11, 2025 at 10:48 pm EST
Answered on: Tuesday, November 11, 2025 at 10:49 pm EST
Question: We recently moved into a sub-divided ranch in Texas. The POA (property owners association) approved a project (in cooperation with the local volunteer fire department) to install a fire water storage tank. The tank was installed but the local electrical contractor was having trouble understanding the discharge pump wiring connections, so they left it disconnected (the pump was supplied by the local volunteer fire department). I have recently agreed to be utilized as an electrical resource, so they asked if I could look at it. The motor wiring was fairly straight forward, but I have some concerns about the motor feeder and branch circuit installation. The 240v feeder OCPD is a 2 pole 60A SquareD QO breaker. Feeder wire is #6 THWN-2 about 60' to a 60A 2 pole 10HP rated non-fused safety switch located near the motor. The motor is connected directly to the load side of the safety switch. The motor nameplate data = 10HP, 230V, 40 FLA, 1.15 SF.The intended application of the tank/motor/pump is to have an interim location to fill fire trucks during emergencies. They'll back in a truck, connect a hose, and fill the truck via discharge motor/pump. We performed a test run today and it took about 10 minutes to fill the truck. The pump remained cool and the motor was warm to the touch. Running amps was 37.Thoughts:My NEC thinking is that a Size 2 motor starter with appropriate overloads should be installed.My practical thinking is that this will work just fine for a little as they are going to use it AND if the are using it, then there's an emergency happening and it would be better to burn up the motor than have it trip on an overload (should an overload condition arise).Questions:Is this something common in rural areas?What would you recommend?Thanks!-William
Okay, William, let's break down this fire pump situation. You've correctly identified a few key areas of concern. Let's analyze the situation based on the NEC and best practices, considering the unique circumstances.
Analysis of Existing Installation
Feeder OCPD (60A)
This might be compliant, but it's on the higher end. We need to calculate the maximum allowed OCPD based on the motor FLA.
Feeder Conductor (#6 THWN-2)
This is the bare minimum. #6 THWN-2 is rated for 55 amps at 75°C (which is where we have to land on this one). The problem with this is that the OCPD is 60 amps. According to 430.52(C)(1), the OCPD shall not exceed the values given in Table 430.
52. The most restrictive is the inverse time breakers. The table states that the max OCPD size shall not exceed 250% of the FLC (40), which is 100 amps. This means the breaker IS sized correctly, but the conductor does not have sufficient ampacity.
Safety Switch (60A, 10HP Rated)
This appears adequate for the application.
Direct Connection to Safety Switch
This is where the problems are going to be. You are going to HAVE to have some kind of overload protection.
NEC Considerations and Calculations
Motor Full-Load Current (FLA) and Service Factor
FLA = 40A Service Factor = 1.152.
Branch-Circuit Short-Circuit and Ground-Fault Protection (Overcurrent Protection)
NEC 430.52 dictates the rules here. As stated above, this portion IS sized correctly.
3.
Motor Overload Protection (NEC 430.32)
This is the biggest concern. The NEC requires overload protection to protect the motor from sustained overcurrent that's less than a short circuit. This is different from short-circuit protection provided by the breaker. Overloads are intended to protect the motor windings from overheating due to things like a jammed pump, low voltage, or excessive load. NEC 430.32(A)(1) and (C)(1) requires overload protection to be sized no greater than 125% of the motor FLA for motors with a service factor of 1.15 or higher. 40A x 1.25 = 50A maximum overload protection. The
critical point is that simply relying on the 60A breaker provides no overload protection. It only protects against a dead short or severe ground fault, not the kind of gradual overcurrent that can cook a motor.4. Feeder Ampacity (NEC 430.24)
The feeder conductors must have an ampacity not less than 125% of the motor full-load current (40A). 40A x 1.25 = 50A.
#6 THWN is rated for 55 amps and IS NOT sized adequately for the ampacity required.
Recommendations
Install a Motor Starter with Overload Protection
This is the correct and NEC-compliant solution. Use a NEMA Size 2 motor starter. Size the overload relays for no more than 50A to provide proper overload protection. Adjust the overload heaters or dial setting according to the manufacturer's instructions for a 40A FLA.2.
Replace Feeder Wire
The #6 THWN-2 is not adequate for the ampacity required by the NEC (50 amps min). Replace with a minimum of #4 THWN-2.3.
Re-evaluate Feeder OCPD
Even though the 60A breaker may be adequate, it may be better to install a 50 amp breaker to better protect the feeder conductors, and provide better coordination.
Addressing Your Concerns
"Burn Up the Motor vs. Trip"
I understand the sentiment, especially in an emergency. However, you can't just throw NEC requirements out the window. A properly sized overload relay will not trip instantaneously under a slight overload. It will trip eventually if the motor is truly overheating, preventing catastrophic failure and potentially a much longer downtime during an emergency. A burned-out motor is useless. A motor that trips on overload can be reset after the problem is addressed.
"Practical Thinking"
While your observations about the motor temperature during the short test are helpful, they are not a substitute for proper protection. A 10-minute test under ideal conditions doesn't account for potential issues in a real-world emergency (e.g., pump cavitation, debris clogging the intake, lower voltage).
Is This Common in Rural Areas?
Unfortunately, yes, it's not uncommon to see installations that cut corners, especially in volunteer or resource-constrained situations. However, that doesn't make it right or safe. As an electrical professional, your responsibility is to advocate for a safe and code-compliant installation.
Priorities
Overload Protection
This is the most crucial fix. The absence of overload protection is a significant hazard. Install the motor starter with properly sized overloads.2.
Feeder Conductor
Replace the feeder wire with #4 THWN-2.3.
Feeder OCPD
Re-evaluate the feeder OCPD, but this isn't a high priority, in my opinion.
Communication
When explaining this to the fire department and POA, frame it this way: "We want to ensure the pump is reliable and available when you need it most." "Proper overload protection prevents the motor from burning out and causing a longer outage." "A code-compliant installation reduces the risk of electrical fire and liability."
In Conclusion:
While the pump might work "fine" for now, the lack of overload protection is a serious issue. Install a motor starter with properly sized overloads. Replace the feeder conductors to the appropriate size. This will provide a safer, more reliable, and code-compliant installation. Flag for review