User: fcfjr, Location: Santa Rosa, California
Asked on: Wednesday, November 12, 2025 at 2:06 pm EST
Answered on: Wednesday, November 12, 2025 at 2:06 pm EST
Question: Hello all, I have a client who wants a hard wired towel warmer located on the wall above the long side of his bathtub. I haven't been able to find anything for fixed electrical heating locations. I know about the zones for devices and light fixtures but am at a loss for a towel warmer. Any help will be greatly appreciated.
You're right to be cautious. Electrical codes prioritize safety, especially around water. While codes might not explicitly forbid a towel warmer above a bathtub, they significantly restrict what you can do and where. Here's a breakdown of considerations and what you should be looking for
1. Understanding the Zones:
Zone 0
Inside the bathtub itself. No electrical equipment allowed.
Zone 1
The area vertically above the bathtub to a height of 2.25m from the floor (or top of the shower head if installed lower). Very restricted.
Zone 2
The area extending 0.6m horizontally beyond the perimeter of the bathtub and up to the same height as Zone 1. Restricted.
2. Code Considerations & Requirements (Most Likely Requiring an Exception)
Generally, permanently connected electrical appliances aren't allowed in Zone 1 or Zone 2. This is because there's an increased risk of accidental contact with water. This is where you'll likely need to seek an exception to local codes. IP Rating
If you can install a towel warmer in Zone 2 (highly unlikely without a variance, but let's assume for the sake of argument), it must have an appropriate IP (Ingress Protection) rating. Specifically, it needs to be protected against splashing water. IPX4 is generally considered the minimum for Zone 2. Look for this rating on the product's specifications. An IP rating tests to see if items can protect the electrical components of the item from outside intrusion.
GFCI Protection
The circuit supplying the towel warmer must be GFCI (Ground Fault Circuit Interrupter) protected. This is non-negotiable. The GFCI will quickly shut off the power if it detects a current leak, preventing electrocution. Confirm that the breaker for this circuit is a GFCI breaker, or that a GFCI receptacle is installed upstream (although a GFCI breaker is strongly preferred).
Wiring
Wiring must be properly rated for wet locations (e.g., THHN/THWN). It should be run through appropriate conduit.
Professional Installation & Inspection
This must be installed by a licensed electrician. And, crucially, it must be inspected by the local electrical inspector. Don't skip this step. It's there to ensure safety and code compliance.
Manufacturer's Instructions
Always follow the manufacturer's installation instructions for the towel warmer. They might have specific recommendations or restrictions based on the product's design.
3. Why This is Problematic (and Likely Requires a Variance)
Height
Even above the bathtub, the towel warmer will likely fall within Zone 1 or Zone 2 unless the bathroom has very high ceilings.
Risk of Splashing
The primary concern is someone accidentally splashing water onto the towel warmer while bathing.
General Safety
Electrical codes prioritize safety. Placing a heating appliance near water inherently introduces risk.
4. Steps to Take
Consult with the Local Electrical Inspector
This is the most important step. Explain what you want to do and ask if it's even possible. They will have the final say and can advise on specific code requirements and potential solutions. Don't start any work until you have their approval. They can also advise if a variance is possible or even available.2.
Consult with a Licensed Electrician
Get a licensed electrician involved early. They can assess the situation, review the electrical code, and determine the best way to install the towel warmer if it's allowed. They can also help with the variance process if needed.3.
Consider Alternatives
Location
Can the towel warmer be installed outside of Zone 2? Even a small shift in location can make a big difference. Consider a different wall.
Freestanding Towel Warmer
Consider a freestanding, plug-in towel warmer. These are not permanently wired and, therefore, generally not subject to the same restrictions as hard-wired units (but still require GFCI protection). Make sure the cord is kept away from the bathtub to minimize the risk of electrocution.
Heated Towel Rack (Water-Based)
These are connected to the hot water system, eliminating the electrical component near the tub. Installation involves plumbing work.
Towel Hooks with In-Floor Heating
Another alternative is to install a small section of in-floor heating underneath the towel hooks on the wall.
In summary, installing a hard-wired towel warmer directly above a bathtub is highly problematic due to safety concerns and electrical code restrictions. It will likely require a variance from the local electrical inspector. Your first step should be to consult with the inspector and a licensed electrician to explore all options and ensure compliance with all applicable codes.
Remember to document all communications and approvals in writing. This will protect you and your client in case of any issues down the road. Good luck! Flag for review