Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: New construction - did someone say hot mess?

User: Skullmesaranch, Location: Cave Creek

Asked on: Wednesday, November 12, 2025 at 4:10 pm EST
Answered on: Wednesday, November 12, 2025 at 4:11 pm EST

Question: Nothing that can't be fixed...This is a continuation of my previous posts. I pulled the wires from the junction boxes today and found about 30% of the combined grounds with no twists (see photo). The remaining grounds had very minimal twists. I unscrewed the nut on connections with multiple hot and neutrals tied together and they fell apart. Only one outlet had the neutral and hot tied together as shown in the photo...I wonder if my electrician would have caught it during top out?

Okay, this is concerning. The fact that you found so many grounding connections without proper twists, along with the hots and neutrals falling apart, is definitely a red flag. Finding a hot and neutral tied together at an outlet is also a serious problem and a significant safety hazard.Here's a breakdown of what you've found and what it means: Poor Grounding Connections (No or Minimal Twists)

This is a fundamental safety issue. Ground wires are designed to provide a path for fault current to return to the source, tripping a breaker and preventing electrocution. Without a good, solid mechanical connection, the grounding system is compromised.
Risk: In the event of a short circuit or ground fault, the ground wire might not be able to carry enough current to trip the breaker quickly enough, potentially resulting in dangerous voltage on appliances, equipment, or even the building's structure. Fix: Each ground wire connection MUST be untwisted, cleaned (if corroded), and properly twisted together using pliers. Then, a proper wire connector (like a green wire nut) must be used to ensure a secure and lasting connection. Consider using crimp-on ground connectors if you're concerned about getting a solid mechanical twist.

Hot and Neutral Connections Falling Apart

The fact that these connections are falling apart is a huge warning sign. Electrical connections must be secure and tight to prevent arcing, overheating, and potential fires. Risk: Loose connections cause resistance, which leads to heat. Over time, this can melt insulation, damage wiring, and start a fire. Fix: All hot and neutral connections need to be completely redone. Use the correct size wire connector for the number and gauge of wires being connected. Ensure a tight, secure fit. Consider pigtailing if needed to reduce the number of wires under each wire connector.

Hot and Neutral Tied Together at Outlet

This is a dead short and a major fire hazard. It's highly unlikely you'd have gotten to this point without other problems or a tripped breaker. It's not clear if this was intentional or accidental.
Risk: Immediate danger of fire, damage to wiring, and potential electrocution. Fix: This must be corrected immediately. The outlet should be disconnected and the wires properly separated and connected to the correct terminals.

Regarding the Electrician



Top Out

Top out is typically done after the wiring is run but before the drywall is installed. It's meant to catch major errors in wire runs and box placement. However, it's unlikely an electrician would be disconnecting every connection to inspect them. While a good electrician should notice obvious issues like loose connections or wires connected incorrectly, it's possible some of these issues could be missed.

Final Connection

The quality of the final connection work is critical. The problems you are finding suggest either sloppy work, or inexperience.

Next Steps (Safety First!)


Turn off the Main Breaker

Before you do anything else, turn off the main breaker to the entire house. This will de-energize all the wiring and prevent any accidental shocks.2.

Document Everything

Take photos of everything you find, both before and after you fix it. This will help you track your progress and provide documentation if you need to show it to a qualified electrician.3.

Fix the Grounding System

Start by correcting all the grounding connections. Untwist, clean, twist tightly with pliers, and use appropriate wire connectors (green wire nuts).4.

Fix the Hot and Neutral Connections

Re-do all the hot and neutral connections, ensuring tight, secure connections with the correct size wire connectors. Pay close attention to the number of wires under each connector. Pigtailing (adding a short length of wire to reduce the number of wires under a connector) is often a good idea.5.

Correct the Hot and Neutral at the Outlet

Correct the wiring at the outlet where the hot and neutral were tied together. Ensure the wires are connected to the correct terminals.6.

Test Your Work

After you've corrected all the wiring, use a non-contact voltage tester to verify that there is no voltage on any of the exposed wires. Then, turn the main breaker back on and test each outlet with a receptacle tester to ensure it's wired correctly and properly grounded.7.

Consider Professional Inspection

Given the extent of the problems you've found, it would be wise to have a qualified electrician inspect your work and the entire electrical system. They can identify any other potential issues you may have missed and ensure that everything is safe and up to code.

Important Considerations



Code Compliance

Make sure you are familiar with the electrical codes in your area. Electrical work must be done to code to ensure safety and prevent future problems.

Permits

Depending on your location, you may need to obtain a permit for electrical work. Check with your local building department.


When in Doubt, Call a Professional

If you are not comfortable working with electricity or if you have any doubts about how to do something, call a qualified electrician. It's better to be safe than sorry.

In summary, you've uncovered some serious issues that need to be addressed immediately. While you can fix them yourself, given the extent of the problems, having a professional electrician inspect the entire system is highly recommended.
Flag for review

Previous Question Next Question