Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Is this statement correct?

User: marcosgue, Location: Tampa

Asked on: Thursday, November 13, 2025 at 6:20 am EST
Answered on: Thursday, November 13, 2025 at 6:20 am EST

Question: Attached paragraph from Oshatoolbox talk that we discused every week in the safety meeting. I think there is a mistake in last sentence of second paragraph because the electrical current travel to ungrounded conductor and return back to the power source of the electrical system through the grounded conductor but never to ground.1. What you guys think about this osha statement?2. Beside a ground fault, is there some specific situation inside the premises where the current travel through the egc back to the electrical system, that we can consider a normal trayectory?

Okay, let's break down the OSHA statement and your questions. Please provide the OSHA statement so I can provide a more accurate assessment. However, I can provide a general response to your questions.1. What you guys think about this OSHA statement?

Without the specific OSHA statement, I can only offer a general critique. Typically, OSHA materials aim to be clear and understandable, even if that means simplifying technical details. Therefore, I will assume that OSHA statement is describing a typical residential or commercial AC power distribution system.

In general, your assessment is correct, the last statement might be confusing. The path electrical current takes in a properly functioning AC circuit is



Source
(Transformer or Generator) -> Ungrounded (Hot) Conductor -> Load (Appliance, Light, etc.) -> Grounded (Neutral) Conductor -> Source.

The Grounding conductor is an alternative path back to the source in case of a fault (short circuit), allowing a high current to flow back to the source that would then trip the circuit breaker.

Why the Confusion Arises



Ground vs. Grounded Conductor (Neutral)

People often conflate "ground" and "grounded conductor (neutral)." The neutral is intentionally connected to ground at the service entrance (and sometimes at the transformer). This connection provides a low-impedance path for fault current to return to the source, facilitating the operation of overcurrent protection devices (circuit breakers or fuses).

Simplification for Understanding

OSHA materials often oversimplify to communicate the basic concept of electrical safety to a broad audience. This can lead to technically inaccurate statements if not carefully worded.

I suspect the OSHA statement aims to convey the importance of grounding and the path electricity takes when a fault occurs. But it is wrong because it implies that the Grounding conductor is the normal return path of the electrical current in a circuit. The grounded conductor (neutral) is.
2. Beside a ground fault, is there some specific situation inside the premises where the current travel through the EGC back to the electrical system, that we can consider a normal trayectory?The answer is NO. In a properly functioning electrical system, current should not flow through the Equipment Grounding Conductor (EGC) under normal operating conditions. Here's why: EGC's Purpose

The EGC's sole purpose is to provide a low-impedance path for fault current to return to the source in the event of a ground fault. It's a safety net.

Current on the EGC = A Problem

If you measure current flowing on the EGC
under normal operating conditions, it indicates one or more of the following issues:

Ground Fault

This is the most likely scenario. Some current is leaking from a hot conductor to ground.

Improper Neutral-Ground Bond

The grounded (neutral) conductor should
only be bonded to ground at the service entrance. If there are additional neutral-ground bonds downstream (e.g., in a subpanel), current can flow through the EGC as it seeks the parallel path back to the source. This is a dangerous situation.

Shared Neutral

Improperly wired multi-wire branch circuits (sharing a neutral) can cause current to flow on the EGC if the loads are unbalanced and wired incorrectly.

EMI/RFI

In certain sensitive electronic equipment installations, very small amounts of current
might flow on the EGC due to electromagnetic interference (EMI) or radio-frequency interference (RFI). This is usually minimal and doesn't represent a safety hazard. However, special grounding techniques are often used in these cases.

Other Wiring Errors

Various other wiring mistakes can cause current to flow on the EGC.

Therefore, any significant current flowing on the EGC under normal operating conditions is a sign of a problem that needs to be investigated and corrected immediately.
In summary: The neutral is the normal return path for current. The EGC is a safety path for fault current.* Current on the EGC under normal conditions is a sign of a problem.Once you provide the OSHA statement, I can give you a more precise evaluation. Flag for review

Previous Question Next Question