Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Kw Rating

User: Alwayslearningelec, Location: NJ

Asked on: Thursday, November 13, 2025 at 11:24 am EST
Answered on: Thursday, November 13, 2025 at 11:25 am EST

Question: At 480v for 150kw I'm coming up with 180A power needed. Does that make sense? Geez that's big wire for these heaters.

Let's break down the calculation and the potential considerations

Calculation
Kilowatts to Watts

150 kW = 150,000 W


Three-Phase Power Formula

P = √3 V I PF (Where P = Power, V = Voltage, I = Current, PF = Power Factor)We need to make assumptions on the power factor. For heaters, the power factor is often very close to 1 (unity). We'll calculate both with unity and .8.

Scenario 1: Power Factor = 1 (Unity)
150,000 W = √3 480 V I 1 150,000 W = 1.732 480 V I 150,000 W = 831.36 I I = 150,000 W / 831.36 = 180.43 AScenario 2: Power Factor = 0.8 (More conservative) 150,000 W = √3 480 V I 0.8 150,000 W = 1.732 480 V I 0.8 150,000 W = 665.09 I I = 150,000 W / 665.09 = 225.5 AConclusion

Yes, your calculation of approximately 180A is correct assuming a power factor of 1. If the power factor is lower (more inductive or capacitive load), the current will be higher.

Why This Matters (Heater Considerations)
Resistive Loads

Heaters are generally
resistive loads, meaning their power factor is usually very close to 1. However, confirm the manufacturer's specifications for the heater's power factor. If it's anything less than 0.9, use the lower power factor calculation.

Nameplate Data

Always use the nameplate data on the heater(s). The nameplate should provide the exact voltage, wattage, and required amperage. This is the most accurate information.

Heater Configuration

Are these multiple heaters wired in parallel? The total current would be the sum of the individual heater currents. Are they wired in a delta or wye configuration?

Wire Sizing and Overcurrent Protection
NEC (National Electrical Code)

Wire sizing and overcurrent protection must comply with the NEC and any local codes. This involves more than just calculating the amperage.

125% Rule

The NEC typically requires that conductors be sized for at least 125% of the continuous load (which heaters often are). So, for the 180A calculation, you'd need to size the conductors for at least 180A
1.25 = 225A. For the 225.5A calculation you'd need to size the conductors for at least 225.5A 1.25 = 281.9A

Ampacity Tables

You'll need to consult the NEC ampacity tables (Table 310.16) to determine the correct wire size based on the ampacity and the insulation type.

Temperature Correction

The ampacity of the wire is also affected by the ambient temperature. If the wiring is in a hot environment, you'll need to derate the ampacity.


Conduit Fill

The number of conductors in a conduit affects the ampacity. You need to apply derating factors if the conduit is heavily filled.

Overcurrent Protection

The overcurrent protection (circuit breaker or fuses) should be sized to protect the conductors and the equipment. The rating of the overcurrent device should not exceed the ampacity of the conductors (after any derating) and should also comply with the heater manufacturer's recommendations.

In Summary and Recommendations
1. Verify Power Factor

Confirm the heater's power factor from the manufacturer's documentation. If in doubt, use a power factor of 0.8 for a more conservative calculation.
2.


Check Nameplate Data

The nameplate on the heater is the definitive source for voltage, wattage, and current.3.

Calculate Current Accurately

Use the correct formula (P = √3
V I PF) and the correct voltage and power factor.4.

Apply the 125% Rule

Size the conductors for at least 125% of the continuous load.5.

Consult NEC Tables

Use the NEC ampacity tables to determine the correct wire size, considering temperature correction and conduit fill.6.

Choose Overcurrent Protection

Select an appropriate overcurrent device (circuit breaker or fuses) that protects the conductors and the heater.7.

Engage a Qualified Electrician:
This is essential! Wiring a 150kW heater is not a DIY project. A qualified electrician will have the knowledge and experience to ensure the installation is safe, code-compliant, and reliable. They can also perform voltage drop calculations to ensure adequate voltage at the heater terminals.Yes, 180A (or higher, depending on power factor) is a significant current, requiring appropriately sized conductors and overcurrent protection. It's not unusual for high-power heaters. Do not underestimate the importance of proper wiring and safety. Flag for review

Previous Question Next Question