User: kjroller, Location: Dawson Mn
Asked on: Thursday, November 13, 2025 at 4:48 pm EST
Answered on: Thursday, November 13, 2025 at 4:48 pm EST
Question: #1 Does anywhere in the code does it say passing through a wall (concrete) is considered a strap or support and securely fastened?#2 If I have a T body coming out of the T body do I need a strap with in 3ft on each pipe entering or exiting the body?I have looked at the code and to me its vague any input is appreciated thank you!
Okay, let's break down these questions and clarify what the electrical code generally requires regarding conduit support, specifically focusing on the scenarios you've described. Keep in mind that code requirements can vary depending on the specific edition of the National Electrical Code (NEC) adopted by your local jurisdiction. Always consult your local electrical code and inspector for definitive answers.Question 1: Passing Through a Concrete Wall as Support No, passing through a concrete wall itself is generally NOT considered a strap or support and securely fastened in the NEC. NEC 300.11 (Securing and Supporting)
This section covers the requirements for securing and supporting raceways (which include conduit). It emphasizes mechanical integrity. While a conduit passing through a concrete wall can provide some inherent stability, it doesn't satisfy the intentional securing/supporting requirements outlined in the code.
Reasoning
The intent of the code is to ensure the conduit is properly supported to prevent strain on connections, maintain raceway integrity, and minimize the risk of damage. The wall offers stability for the conduit but is NOT a strap, tie or clamp designed and installed for the support and fastening of conduit.There is NO securing or support to be expected.
Additional Considerations
Clearances
The concrete itself may have minimum clearance requirements that if done, it is not considered support.
Expansion/Contraction
If there is no securing or support of the conduit within the concrete, expansion and contraction could possibly cause issues.
Question 2: Strapping Requirements Around a Conduit Body (T-Body)This is where the code gets a little more nuanced, and interpretations can vary. Here's a breakdown:
General Requirement (NEC 314.30)
Conduit bodies must be rigidly and securely fastened in place.
The 3-Foot Rule and Conduit Bodies
The common "3-foot rule" refers to the general support requirements for conduit runs between boxes and fittings.
However, it doesn't automatically apply to every single pipe entering or exiting a conduit body. The need for support within 3 feet of a conduit body depends on several factors:
Short Nipples
If you have very short nipples (e.g., a few inches) coming out of the T-body and directly entering other equipment or boxes that provide support, additional strapping might not be necessary.
Total Lengths
If the total run of conduit leaving the T-body is short and inherently stable, strapping right at the T-body might not be required, especially if the run continues to a securely mounted enclosure or fitting within a short distance.
Conductor Fill
If the conduit is heavily filled with conductors, requiring additional support.
Conduit Size
Smaller conduit sizes (e.g., 1/2", 3/4") generally need closer support than larger sizes.
Material
EMT, Rigid Metal Conduit (RMC), PVC, and Flexible Metal Conduit (FMC) each have different support requirements in the NEC.
Vibration/Physical Damage
If the area is subject to vibration or physical damage, more frequent support is necessary.
Key Consideration: Support of the Overall System The goal is to ensure the entire conduit system is securely supported. If the T-body is itself well-supported, and the conduit runs entering and exiting it are short and stable, the need for additional strapping immediately at the T-body might be reduced. However, this is a judgment call. When Support NEAR a T-Body is Definitely Needed
Long Runs
If the conduit runs leaving the T-body are long and unsupported, a strap within 3 feet of the T-body is likely necessary to prevent strain on the T-body and the connections within it.
Heavier Conduit
If you are using a large size of conduit or a metal such as RMC, needing strapping within 3 feet of the T body would be more ideal.
Specific Local Requirements
Some jurisdictions have stricter interpretations and may require strapping within 3 feet of every conduit body regardless.
Best Practices and Recommendations
Consult Your Local Electrical Inspector
This is the most important step. Ask them for their specific interpretation of the code for your project.2.
Err on the Side of Caution
When in doubt, provide more support. It's better to over-support than under-support.3.
Document Your Installation
Take pictures of your conduit runs, especially showing support locations. This can be helpful during inspections.4.
Use Approved Straps and Hangers
Make sure you're using straps and hangers that are listed for the type of conduit you are using.
In Summary: A concrete wall itself does not fulfill the requirement for a strap or support.* The need for strapping within 3 feet of a T-body is situational. Consider the length and stability of the conduit runs, the size and type of conduit, the overall support of the system, and your local code requirements.Remember to always consult your local code and inspector for the most accurate guidance. Flag for review