Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Transfer Switch Conduit Routing

User: kcunningham59, Location: Audubon, NJ

Asked on: Thursday, November 13, 2025 at 11:55 pm EST
Answered on: Thursday, November 13, 2025 at 11:55 pm EST

Question: I had a 1200A Asco Transfer Switch with 8 conduits coming in from the 2 sources. I need to go back out with 4 sets of conduits underground again to the final destination. That’s a lot of conduits in and out of this switch. Would you guys come out the side into a pull box and then go underground? Into LB’s the down?

Okay, you've got a congested situation at your transfer switch! Managing that many large conduits is a common challenge. Here's a breakdown of factors to consider and a discussion of your suggestion (and other possible solutions)

Understanding the Problem
Physical Space

The primary issue is the physical congestion around the transfer switch. Cramming that many conduits in and out directly is difficult for installation, maintenance, and future modifications.


Bending Radius

Large conduits, especially with larger conductors, have minimum bending radius requirements. Trying to make sharp turns directly at the switch could violate code and damage conductors.

Pulling Effort

Pulling conductors through multiple bends (especially 90-degree LB fittings) significantly increases pulling tension. Exceeding the allowable pulling tension can damage conductors.


Accessibility

Future access for troubleshooting, maintenance, and conductor replacement is essential. A dense cluster of conduits makes this difficult.

Code Compliance

You must adhere to the NEC (National Electrical Code) or your local electrical code, which covers conduit fill, bending radii, support requirements, and working clearances.

Evaluating Your "Pull Box" Suggestion


Your idea of transitioning to a pull box is a good starting point. Let's break it down:
Pros



Decoupling

The pull box decouples the tight conduit layout at the transfer switch from the underground run. This simplifies the immediate connections to the switch.


Space Management

The pull box provides more space to manage the conductors as they transition from the 8 incoming conduits to the 4 outgoing conduits. You can make larger, code-compliant bends within the box.

Easier Pulling

You can perform conductor pulls in shorter segments. You can pull the conductors from the source equipment to the Pull Box, then pull from the Pull Box to the transfer switch. This can significantly reduce pulling tension.


Accessibility

The pull box provides a point of access for future conductor inspections, testing, and potential replacements.

Cons



Cost

Pull boxes and their associated installation add to the overall project cost.

Space Requirement

The pull box itself requires physical space, which might be a constraint.


Water Intrusion

Underground pull boxes are susceptible to water intrusion. Proper sealing and drainage are critical.

LB Fittings Directly into the Ground
Pros



Simplicity

The design seems simple.

Cons



Accessibility

Makes pulling and future maintenance very difficult.

Conductor Damage

The number of bends increase the possibility of conductor damage.

Alternative Solutions & Considerations
1. Sizing the Pull Box



NEC Requirements

NEC Article 314 covers pull boxes, junction boxes, and handhole enclosures. It specifies minimum dimensions based on the size and number of conductors entering and exiting the box. You must calculate the minimum pull box size according to the code.

Straight Pulls

For straight pulls, the length of the box must be at least eight times the trade diameter of the largest raceway.


Angle or U Pulls

For angle or U pulls, the distance from each raceway entry to the opposite wall of the box must be at least six times the trade diameter of the largest raceway, plus the sum of the diameters of all other raceways on the same wall and row. This is a more complex calculation.

Depth and Width

You also need adequate depth and width to properly arrange the conductors within the box.


Oversizing

It's generally a good idea to slightly oversize the pull box to provide more working space and accommodate future changes.2.

Conduit Material and Installation



RMC (Rigid Metal Conduit)

Offers the best physical protection for underground runs.


IMC (Intermediate Metal Conduit)

A lighter-weight alternative to RMC, offering good protection.

PVC (Polyvinyl Chloride Conduit)

A cost-effective option, but requires more care in installation to prevent damage and requires proper burial depth for physical protection.


Expansion Fittings

If using PVC conduit, use expansion fittings to accommodate thermal expansion and contraction.

Sealing

Properly seal all conduit connections and the pull box to prevent water intrusion.3.

Conductor Selection and Pulling



Conductor Type

Use conductors rated for wet locations (e.g., THWN-2, XHHW-2).

Conductor Size

Verify conductor ampacity based on the load and NEC requirements.


Pulling Compound

Use a listed pulling compound to reduce friction during conductor installation.*

Pulling Equipment

Use appropriate pulling equipment to avoid exceeding conductor pulling tension limits. Consider using a dynamometer to monitor pulling force.4.

Consider "Ganged" Multiple Smaller Transfer Switches

Depending on the load, instead of a single 1200A switch, look into a design with multiple smaller paralleled transfer switches. This can reduce the conduit size significantly.

Recommendations
1. Detailed Load Calculation

Review the load calculations to confirm the 1200A service is correct. Optimize conduit fill with paralleled conductors if necessary to minimize conduit size.2.

Consult with an Electrical Engineer

Given the complexity of the situation, it's highly recommended to consult with a licensed electrical engineer experienced in power distribution systems. They can perform the necessary calculations, develop a detailed design, and ensure code compliance.3.

Select a High-Quality Pull Box

Choose a pull box rated for underground use with a watertight cover. Consider materials like fiberglass or polymer concrete, which are resistant to corrosion.4.

Plan the Conduit Layout Carefully

Develop a detailed conduit layout, considering bending radii, support requirements, and accessibility.5.

Pulling Calculations

Perform pulling calculations to estimate pulling tension and select appropriate pulling equipment.

In summary, using a pull box to transition between the transfer switch and the underground conduits is a viable solution, but it needs to be carefully planned and executed. Consulting with an electrical engineer is highly recommended to ensure a safe, reliable, and code-compliant installation.
Flag for review

Previous Question Next Question