Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Brand new breaker bad

User: solarken, Location: Hudson, OH, USA

Asked on: Saturday, November 15, 2025 at 12:05 pm EST
Answered on: Saturday, November 15, 2025 at 12:10 pm EST

Question: I went to turn up a solar PV system yesterday for the first time, and found the brand new Siemens QP breaker I used for backfed connection had one open pole. Job was 90 minutes away. Anyone have any thoughts on how often a breaker is bad right out of the box? Not sure if this was a fluke or if I need to check every breaker I buy or always buy 2.

That's definitely a frustrating situation! Having a breaker fail out of the box is rare, but it does happen. Here's a breakdown of the potential causes, what to do, and how to minimize future issues

Likely Causes:
Manufacturing Defect

This is the most probable reason. Breakers are complex electromechanical devices, and occasionally a component will be faulty or improperly assembled. Even reputable brands like Siemens can have a small percentage of failures.


Shipping/Handling Damage

While less common, breakers can be damaged during shipping and handling. A sharp jolt or impact could affect the internal mechanisms.

Internal Trip Mechanism Fault

It's possible the trip mechanism on that pole was overly sensitive or defective. This could cause it to trip immediately even with no fault condition.


Over-tightening Screws

It is possible, but unlikely, that the screws used to fasten conductors were so overtightened that it damaged the breaker or its internal mechanism.

What to Do Now



Return/Exchange

The most important thing is to get the breaker replaced. Contact the supplier where you purchased the breaker and explain the situation. They should be able to provide a replacement under warranty.


Inspect the Wiring

Even though the breaker was likely the issue, carefully inspect the wiring to the inverter and the connection to the breaker. Rule out any obvious wiring errors or shorts that could have contributed (however unlikely).

Document the Failure

Keep a record of the failed breaker (model number, date of purchase, date of failure). This can be helpful if you experience similar issues with that supplier/brand in the future.

How to Minimize Future Issues



Quality Brands

Stick with reputable brands of breakers. While no brand is immune to failures, established brands generally have better quality control processes. Siemens is usually considered a good brand.

Visual Inspection

Before installing any breaker, give it a quick visual inspection. Look for any obvious signs of damage (cracks in the housing, loose components, bent terminals). This won't catch internal defects, but it can identify problems caused by shipping damage.


Electrical Testing

This is not generally done in the field on new breakers, but could be done on a random sample if the user has a high level of concern.

Test with a Meter (if possible)

Before installing the breaker, you can use a multimeter to test continuity across each pole of the breaker in the OFF position. All poles should show open. When switched ON, each pole should show continuity.
This is a basic test but can catch a completely dead pole before installation.

Important

Only do this with the breaker disconnected from any power source.


Consider a Backup Breaker

For critical installations (especially when travel time is significant), carrying a spare breaker of common sizes can be a good idea. This adds to your upfront cost, but can save significant time and expense if a breaker fails.

Proper Installation

Ensure the breaker is properly seated in the panelboard and that all connections are torqued to the manufacturer's specifications. Over-tightening screws can damage the breaker or the wiring.


Feedback to Supplier

Let the supplier/manufacturer know about the failure. This feedback helps them track potential quality issues.

How Often Do Breakers Fail Out of the Box?


There's no definitive industry-wide statistic. However, a reasonable estimate for a reputable brand would be a failure rate of less than 1%. Breakers are generally very reliable components, so a failure rate higher than that would be cause for concern.

In Conclusion:

Having a breaker fail out of the box is unusual, but not unheard of. The most likely cause is a manufacturing defect. Focus on getting the breaker replaced under warranty and taking steps to minimize the risk of future occurrences. Don't let this one experience discourage you – breakers are typically reliable components! Flag for review

Previous Question Next Question