Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Bosch Dtect200C wall scanner

User: electrofelon, Location: Cherry Valley NY, Seattle, WA

Asked on: Sunday, November 16, 2025 at 10:34 am EST
Answered on: Sunday, November 16, 2025 at 10:34 am EST

Question: Well I did it, I bought one. The primary impetus was I was doing a roof mounted PV system, and although the attachments I was using do not specifically require hitting a rafter, missing requires more screws which are more penetrations, and is just all around less ideal. Also for some time I have wanted a wall scanner that can find studs thru plaster and lath because I like using side screw boxes instead of old work boxes. IT worked flawlessly and was super accurate. Highly recommend. I did find that, at least for this application, use the signal graph mode. The screen shows a graph of the reflectivity (or whatever) and the top of the curve is the center.Maybe I should have posted this in the PV forum, but what do you guys use to find rafters/trusses? Or dont you?

Congratulations on the purchase of your stud finder! It sounds like it's already paying dividends with your PV installation and your work with plaster and lath. Finding rafters/trusses accurately is crucial for a secure PV installation, so your investment makes perfect sense.Here's a breakdown of what I've used, along with thoughts on each

1. Stud Finder (Like Yours!):
Pros

As you've discovered, newer stud finders, especially those with deep scan modes and signal graph features, can be incredibly accurate, even through challenging materials like plaster and lath. They can also detect the edges, which helps you visualize the width of the rafter/stud.


Cons

Accuracy can still be affected by inconsistencies in the wall/roof material (dense plaster spots, metal mesh, etc.). Requires batteries. Can be tricky to use overhead (gravity can work against you).

When I Use It

My
first line of defense. I've found that combining a good stud finder with common sense techniques (see below) gives the best results. Especially valuable for plaster/lath walls where standard stud finding methods are unreliable.

2. "Knock Test" and Sound



Pros

Free! Simple. Can quickly give you a general idea of where studs/rafters might be.

Cons

Not precise at all. Almost useless for thicker materials or when there's a significant void space. Highly subjective.


When I Use It

A quick and dirty initial assessment, especially in areas I suspect a rafter/stud should be (e.g., near corners of walls or at regular intervals).

3. Measuring from a Known Reference Point



Pros

Reliable if you know the on-center spacing and have a known starting point.


Cons

Requires a known reference (like an outside wall). Assumes perfect, consistent spacing, which is not always the case, especially in older homes. Small errors can accumulate over distance.

When I Use It

After finding one rafter/stud, I use a measuring tape to
predict the location of the next one, based on the expected on-center spacing (typically 16" or 24"). This helps to narrow down the area for the stud finder.

4. Visual Clues



Pros

Free! Relatively simple.

Cons

Only works if visual clues are present.


When I Use It

Look for nail patterns, slightly raised sections of the roof, or other subtle visual indications.

5. Small Test Hole



Pros

Definitive.


Cons

Leaves a hole that needs to be patched.

When I Use It

Only when I'm truly unsure and
absolutely need to know the exact location. I use the smallest drill bit I can get away with, and I drill in an inconspicuous spot. Usually a last resort.

6. Strong Magnet



Pros

Very effective for finding screws or nails in drywall or plaster, indicating the location of the stud.

Cons

Doesn't work well with plaster and lath, as the lath often interferes with the magnet.


When I Use It

Primarily for drywall walls where I need to locate fasteners.

Regarding PV Installations - Important Considerations



Rafter/Truss Spacing

Be absolutely sure you know the
actual on-center spacing of your rafters or trusses. Don't just assume! Measure multiple spans to confirm consistency.

Load Requirements

Make sure the attachments you're using are properly rated for the load of the PV system, taking into account wind and snow loads in your area. Your local building codes likely have specific requirements for PV mounting.

Flashing and Sealing

Proper flashing and sealing around any penetrations in the roof are crucial to prevent leaks.


Professional Consultation (Potentially)

If you are at all unsure about any aspect of the installation, consider consulting with a qualified structural engineer or PV installation professional. Rooftop PV systems can be very heavy, and improper installation can lead to serious structural damage or even collapse.

In summary:
Your new stud finder is a great tool, but I always recommend a multi-pronged approach to finding rafters/trusses, combining technology with careful observation and, when necessary, direct verification. Stay safe and happy installing! Flag for review

Previous Question Next Question