Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Service Entrance Equipment Mounting Board Covering?

User: paullmullen, Location: Wisconsin

Asked on: Sunday, November 16, 2025 at 9:02 pm EST
Answered on: Sunday, November 16, 2025 at 9:02 pm EST

Question: I am mounting the meter cabinet and disconnects for a new service to a piece of plywood to permit insulation between the entrance equipment and the wall sheathing. The picture tells the story. My question is "What are people using to treat the plywood or cover it so that it becomes maintenance free" (no painting needed in the future).Options considered but problematic in some form:- marine painted board. (Still needs painting in the future.)- Stainless steel covering. (Pretty, but $$$, and and extra EGC for just the cover.)- PVC over plywood (Nice solution, but PVC is usually not long-term UV stable)- Aluminum (Galvanic corrosion with steel components mounted to it)- Powder Coated something or other ($$$)What have others done?

Okay, this is a common situation and you're right to think about longevity and maintenance-free solutions. Let's break down the considerations and some potential solutions, keeping in mind cost-effectiveness.

Understanding the Problem



Moisture

Plywood is susceptible to moisture absorption, leading to rot, delamination, and eventual failure.


UV Exposure

While often indoors, the plywood could still be exposed to indirect UV that degrades the wood and any coatings.

Maintenance

The goal is to avoid future painting or other upkeep.


Galvanic Corrosion

You've rightly identified this as a concern with aluminum.

Evaluation of Your Options



Marine Painted Board

You're correct, even with high-quality marine paint, it will eventually require maintenance. The life of the paint depends a lot on the number of coats applied and the specific conditions it is installed in.


Stainless Steel Covering

Excellent durability, but the cost is a major drawback. The EGC issue is also a factor.

PVC over Plywood

PVC
can be UV-sensitive. You'd need to ensure it's a UV-stabilized formulation. The cost of the PVC is also pretty high.

Aluminum

Galvanic corrosion is a significant concern unless you meticulously isolate every steel component (washers, standoffs, etc.), which is impractical.

Powder Coating

Durable, but as you said, cost can be prohibitive.

Other Considerations and Potential Solutions

Here's where we start thinking outside the box a bit:1.

Exterior Grade Plywood with a Modified Acrylic Coating



Plywood

Use Exterior Grade plywood (e.g., ACX plywood). This is designed to withstand moisture. Do not use interior grade plywood.

Coating

Forget painting and go for a high-build modified acrylic coating. This is typically used for industrial applications or for commercial roofing.


Pros

Excellent UV resistance, flexibility to handle expansion and contraction of the wood, good moisture protection, and long lifespan.

Cons

More expensive than paint but much longer lasting, application can be tricky.


Application

Apply a primer coat compatible with the acrylic, then two or three thick coats of the acrylic itself.2.

Fiberglass Reinforced Panel (FRP) Sheeting over Plywood



Plywood

Exterior grade plywood again.


FRP Sheeting

This is a thin, durable, and waterproof material commonly used in commercial kitchens and bathrooms. It's available in sheets that can be easily cut and fastened.

Pros

Very durable, waterproof, easy to clean, relatively inexpensive, UV resistant (check the specific product), and available in various colors.


Cons

Requires mechanical fasteners (screws/rivets) and adhesive.

Application

Glue the FRP to the plywood with a suitable construction adhesive (follow adhesive instructions). Secure with screws or rivets around the perimeter and potentially in the field.3.

HDPE (High-Density Polyethylene) Sheet



Pros

Very durable, waterproof, UV resistant, chemical resistant, won't rot, and relatively inexpensive.

Cons

Can be harder to work with than FRP, may require pre-drilling for fasteners. May require special fasteners.


Application

Fasten to the plywood using appropriate screws and washers. You may need to use a countersinking bit to ensure the screw heads are flush.4.

Cement Board



Pros

Completely impervious to moisture, fire-resistant, dimensionally stable.


Cons

Heavy, more brittle than plywood, requires special cutting tools, and can be more expensive. Fastening can be tricky.

Application

Requires specific screws designed for cement board.

Why I recommend FRP or HDPE over the others


Based on your constraints and goals, FRP or HDPE offer the best balance of cost, durability, and ease of installation.
Cost

More affordable than stainless steel or powder coating.

Durability

Excellent resistance to moisture and UV degradation.


Maintenance

Virtually maintenance-free.

Installation

Relatively easy to cut and fasten (compared to cement board or some metal options).

Important Considerations for ANY Solution



Fasteners

Use stainless steel or exterior-grade, coated fasteners to prevent corrosion.*

Sealing

Seal any penetrations (e.g., for conduit) with a weatherproof sealant.

Recommendation:


I would suggest seriously considering the FRP sheeting or HDPE sheet options. They offer a good balance of cost, durability, and ease of installation. Exterior grade plywood is an absolute must, regardless of the covering. Good luck with your project! Flag for review

Previous Question Next Question