Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: Service size after reducing Main breaker size

User: Sierrasparky, Location: USA

Asked on: Monday, November 17, 2025 at 11:47 am EST
Answered on: Monday, November 17, 2025 at 11:47 am EST

Question: Hello,I am not a solar contractor however I would like to understand the methodology in calculating new loads when a PV system is installed and the Main breaker size is reduced to accommodate a larger array?Example is you have a 200a all in one and you reduce the main breaker to 150 in order to have a greater back-feed. I want to know what the new panel rating is for load calculations is. Is it still a 200a or a ?

You're asking about a common and critical calculation in solar installations. Here's a breakdown of how to determine the new allowable load with a reduced main breaker size, focusing on the NEC (National Electrical Code) principles

Key NEC Sections to Understand:
NEC 705.12(B)(2)(b)

This is the core of this calculation. It deals with the "120% Rule" when the sum of overcurrent devices (breakers) exceeds the busbar rating.


NEC Article 220

This covers branch-circuit, feeder, and service calculations for general loads.

The 120% Rule and its Application


The 120% rule is designed to ensure that the total current allowed on a panel busbar does not exceed 120% of its rating.Here's how it works in your scenario:1. Busbar Rating

Your all-in-one panel likely has a busbar rating matching the original main breaker – in your case, 200A. This is crucial. You need to confirm the busbar rating on the panel itself. Sometimes the main breaker is smaller than the busbar rating, but this method assumes they are the same.2.

Calculating Maximum Allowable Combined Current

Multiply the busbar rating by 120%: 200A (Busbar) 1.20 = 240A3.

Determine Existing Overcurrent Protection (Main Breaker and PV Breaker)

You've reduced the Main Breaker to 150A. You are adding a PV breaker (let's assume it's a 50A breaker for this example).4.

Calculate the Maximum Allowable PV Breaker Size

Using the 120% Rule, determine the largest PV breaker you can have while adhering to the 240A limit. 240A (Maximum Combined) - 150A (Main Breaker) = 90A This is the absolute maximum size of your PV breaker.5.

Calculate the New Maximum Load

The maximum load is limited by what you can draw after accounting for the backfed PV power. Using your 50A PV breaker (from the assumption earlier):
240A(Maximum Combined) - 50A (PV Breaker) = 190A This is how many amps are available for your existing load.6.

Important Considerations



Continuous Load

Remember NEC rules about continuous loads (loads expected to be on for 3 hours or more). Continuous loads are limited to 80% of the breaker rating. This affects your calculations of individual branch circuit sizes.


Load Calculations

You must perform a proper NEC Article 220 load calculation for the house to determine if reducing the main breaker is even feasible. This calculation considers all the appliances, lighting, and other loads in the house.

Local AHJ (Authority Having Jurisdiction)

Always consult with your local building department or electrical inspector. They have the final say and may have specific interpretations or requirements beyond the basic NEC.


Panel Labeling

After the installation, the panel must be clearly labeled indicating the presence of the PV system and the adjusted maximum allowable current.

Example Scenario (Your Numbers)
Original Main Breaker: 200A New Main Breaker: 150A Busbar Rating: 200A (Assuming the busbar rating matches the original main breaker. Verify this!)1. Maximum Combined Current

200A (busbar)
1.20 = 240A2.

Let's say you want to install a 60A PV breaker (hypothetical)

3.

Maximum Combined Current Verification

150A (Main) + 60A (PV) = 210A. This is less than 240A, so the 120% rule is satisfied for the busbar.4.

Calculate the New Maximum Load

240A (Maximum Combined) - 60A (PV Breaker) = 180A5.

Available Load Calculation

To determine the actual available load, you must account for the main breaker limitation. Since the 150A main breaker is the service disconnect. This means 150A available for load. This is the overall constraint to meet, the 120% rule simply allows some of the PV breaker to increase this value up to a max of 240A.

Why This Matters
Safety

Prevents overloading the electrical panel, which could lead to overheating, fires, and equipment damage.


Code Compliance

Ensures the installation meets NEC requirements and avoids potential red-tagging during inspection.

Proper System Operation

Prevents nuisance tripping of breakers and ensures the PV system operates correctly without negatively impacting the home's electrical system.

Disclaimer:
I am an AI Chatbot and not a licensed electrician or solar installer. This information is for general understanding only and should not be taken as professional advice. You MUST consult with qualified professionals for any electrical work.* Flag for review

Previous Question Next Question