Mike Dolt Enterprises Logo Mike Dolt Enterprises

Topic: LED Undercabinet Lighting wired with Cat5 Cable (opinions please)?

User: busman, Location: Northern Virginia

Asked on: Monday, November 17, 2025 at 3:54 pm EST
Answered on: Monday, November 17, 2025 at 3:54 pm EST

Question: All,Doing this for a customer of mine (also a friend). Anyway, they called me the other day because LED UC lights were flickering. I get there and find a power supply that is NOT class 2 or class 3. From memory, I want to say the driver had a maximum output of 16A at 12V. Anyway, the wiring (I couldn't get a look at the sheathing) looks exactly like Cat5 cable and the ends where it is connected (see photo) are Green and Green/White indicating that it is almost certainly a pair from Cat5 (photo shows the splice to the LED light). There are three separate cables at the power supply, so one option might be to get three Class 2 power supplies and put one on each cable (I don't know the wattage of each light yet).Anyway, I told the customer I would poll for your opinions on here without coloring the response in any way with my own opinions.I have more work than I can take on, so your answers will NOT eat into my paychecks, so be brutally honest please as I know this crowd always is.Thanks again for taking a second to help with this.Mark

Okay, Mark, here's a brutally honest breakdown of the situation and some advice, keeping in mind safety, code compliance, and best practices.

What's Wrong (Beyond Just Flickering)



Cat5 Cable is COMPLETELY Inappropriate

This is a major problem. Cat5 is designed for low-voltage, low-current data transmission. Using it for power delivery, especially at 12V with potentially high amperage (even
with a Class 2 power supply), is a fire hazard waiting to happen. The conductors are too small to handle the current, leading to overheating, insulation breakdown, and potentially fire. This is not a matter of "opinion," it's a code violation and dangerous. The flickering is likely partially (or fully) caused by voltage drop due to the undersized conductors.

Non-Class 2 Power Supply with Low Voltage Lighting = Code Violation (Likely)

Modern electrical codes are very strict about low-voltage lighting. You are almost certainly violating electrical code by having a non-class 2 power supply running these lights.

16A at 12V is Potentially High Amperage

Even if it
were a Class 2 supply, 16A at 12V is still a substantial amount of current. Using undersized wiring (like Cat5) to deliver that much power over any significant distance is just asking for trouble.

Poor Wiring Practices

The splice shown in the photo looks haphazard. Proper wire connectors appropriate for the voltage and amperage are essential.

Unknown LED Load

You need to determine the wattage of
each LED light/fixture. This is crucial for selecting appropriate power supplies and wiring.

What Needs to Happen (In Order of Importance)


IMMEDIATE SAFETY CONCERNS

Disconnect the non-Class 2 power supply. Tell your friend that this setup is unsafe and needs to be corrected
before the lights are used again. The risk of fire is real.2.

Inspect All Wiring

Carefully inspect the wiring
from the power supply to the LEDs. Determine the gauge and type of the entire run, not just the visible splice. Even if some portions are appropriate, the Cat5 section makes the entire run suspect.3.

Determine LED Wattage

Find the wattage rating of each LED light/fixture. Look for labels on the fixtures themselves. If necessary, you can use a multimeter to measure the current draw of each fixture and calculate the wattage.4.

Proper Wiring



Low-Voltage Landscape Lighting Cable

Use UL-listed low-voltage landscape lighting cable for all connections. This cable is designed for direct burial and outdoor use. 12/2 or 14/2 gauge is common, but the appropriate gauge depends on the wattage of the lights and the distance of the run (to minimize voltage drop).

Wire Connectors

Use weatherproof wire connectors appropriate for low-voltage landscape lighting.


Proper Routing and Protection

Ensure wiring is routed and protected according to code (e.g., buried to the correct depth, protected in conduit where exposed to damage).5.

Class 2 Power Supplies

Use Class 2 power supplies for each run of lights. These are current-limited and designed to prevent overheating and fires. The power supply must be sized appropriately for the wattage of the LED lights connected to it, with some headroom (e.g., 20% extra capacity).6.

Consider Voltage Drop

Calculate the voltage drop for each run of lights, considering the wire gauge, length of the run, and current draw. Use a voltage drop calculator to ensure the voltage at the LEDs is within the acceptable range. If voltage drop is excessive, you'll need to use a heavier gauge wire or multiple power supplies closer to the lights.7.

Code Compliance

Ensure all work complies with local electrical codes and regulations. If you're not comfortable with electrical work, hire a qualified electrician.8.

Consider a Qualified Electrical Contractor

If there is any doubt at all, recommend the use of a qualified electrician. This has the potential to cause serious harm to property and persons.

Your Options (Based on the Information So Far)



Option 1 (Recommended - Most Correct)

Remove all existing wiring and replace it with low-voltage landscape lighting cable. Install separate Class 2 power supplies for each run of lights, sized appropriately for the wattage of the lights. Use weatherproof wire connectors and follow proper routing and protection practices.

Option 2 (If the Existing Wiring, OTHER than the Cat5, is Acceptable)

Remove the Cat5 completely. Inspect the remaining wiring and verify that it is the correct gauge and rated for the use. Replace the non-Class 2 power supply with suitable Class 2 power supplies. Ensure that the connections are up to code.

What You Need to Tell Your Friend

The current setup is unsafe and poses a fire hazard. It must be corrected. Using Cat5 cable for power is a serious mistake. They need to determine the wattage of each light fixture. They need to budget for new wiring, connectors, and power supplies. If they're not comfortable with electrical work, they should hire a qualified electrician.* Suggest to your friend that they should do nothing until you can determine the nature of the rest of the wiring.

In summary:
Don't mess around with this. It's not just about flickering lights; it's about safety and code compliance. Prioritize getting the wiring and power supplies corrected properly. Let me know if you have more questions. Good luck! Flag for review

Previous Question Next Question