User: Sup, Location: Canada
Asked on: Monday, November 17, 2025 at 6:37 pm EST
Answered on: Monday, November 17, 2025 at 6:41 pm EST
Question: Untwisting MC(Bx) cable wires after stripping the sheathing off (especially when you're doing a panel) has got to be one of the most annoying things. I'm not alone am I? Maybe share your tips if you have some please?
You're absolutely not alone! Untwisting MC/BX cable wires after stripping the sheathing is a universal annoyance for electricians. It's time-consuming, can be hard on your hands, and makes for a messy-looking panel. Here are a few tips and tricks I've picked up (and others commonly share) to make the process a little less painful
Tools & Techniques:
Good Quality Tools are Key
Sharp Cable Cutter
A dedicated MC cable cutter (like the Ideal MC Cable Cutter or similar) is a game-changer. They shear the armor cleanly and minimize distortion, which makes untwisting easier. A dull cutter just mangles the armor and makes the wires even harder to separate.
Stripper/Cutter Combo
Consider having a combination wire stripper/cutter that can handle MC cable. Some models are designed to quickly and cleanly strip the armor without damaging the wires.
Needle-Nose Pliers (Long-Nose)
These are indispensable for grabbing individual wires and pulling them apart, especially in tight spaces.
Proper Armor Removal
Score Lightly
Avoid cutting too deeply into the armor on the first pass. A light score around the cable is often enough. You can then bend the cable at the score, and it should separate more easily.
Spiral Cut
If you can't get a clean break, try making a shallow, spiral cut around the armor. This can relieve the tension and make it easier to peel back.
Red Head/Bushing
Always use a red head or appropriate bushing to protect the wires where they exit the armor. This prevents chafing and potential shorts.
The "Grab and Twist" Method
Separate Ground First
If there's a ground wire (bare or green), try to isolate and pull that out first. It often gets tangled with the insulated conductors.
Grab Firmly
Use your needle-nose pliers to firmly grab one wire as close to the cut edge of the armor as possible.
Twist and Pull
Gently twist the wire back and forth while simultaneously pulling it away from the other wires. The twisting motion helps loosen it from the tightly packed bundle.
Repeat
Repeat the process for each wire, working your way around the cable.
The "Armor Spread" Method (Carefully!)
Patience
This requires a delicate touch. After removing the armor, try to gently spread the cut end of the armor open slightly. This can create a little more space to work with.
Avoid Damage
Be extremely careful not to kink or damage the wires when spreading the armor.
Pry with a Small Screwdriver (Carefully!)
A very small, flat-head screwdriver can be used to gently pry individual wires away from the others. Again, be very cautious not to damage the insulation.
Work in Stages
Strip, Untwist, Repeat
Don't try to strip a long length of armor and then untwist all the wires at once. Work in shorter segments (e.g., strip 6-8 inches, untwist, then strip another 6-8 inches). This gives you more control and reduces the likelihood of tangling.
Lubrication (Use Sparingly and with Caution)
Wire Lube
A tiny amount of wire-pulling lubricant (the stuff used for pulling wires through conduit) can sometimes help the wires slide past each other. Apply sparingly and only if absolutely necessary.
Avoid Contamination
Be careful not to get lubricant on the wire insulation or inside the panel, as it can attract dust and debris.
Panel Specific Tips
Plan Your Runs
Carefully plan your cable runs to minimize bends and sharp turns. This will make pulling and untwisting the wires easier.
Leave Extra Length
Leave a generous amount of wire inside the panel. It's always better to have too much than not enough. You can always trim it later.
Organize as You Go
As you untwist and connect each wire, immediately organize it in the panel. This will prevent a tangled mess from accumulating. Use cable ties or wire managers to keep things neat and tidy.
Dress the Wires
"Dressing" the wires (bending them neatly and routing them properly) is an art form. It takes practice, but it makes for a much cleaner and more professional-looking panel.
General Advice
Practice
Like anything else, untwisting MC cable gets easier with practice. Don't be afraid to experiment with different techniques to find what works best for you.
Patience
Don't rush the process. Trying to force the wires apart will only make things worse.
Sharp Cutters
Ensure your cutters are sharp to avoid deforming the metal jacket.
Take Breaks
If your hands are getting tired, take a break. Untwisting MC cable can be physically demanding.
Consider Alternatives
While MC/BX is very common, depending on your local codes and the application, you might be able to use flexible metal conduit (FMC) with THHN wires. While that has its own set of challenges, some electricians find it easier to work with in certain situations.
Why is it so annoying? Tight Packing
The wires are packed very tightly inside the armor, making them difficult to separate.
Friction
The metal armor can create a lot of friction, making it hard to pull the wires out.
Tension
The twisting of the armor can put tension on the wires, making them even more difficult to untwist.*
Sharp Edges: The cut edges of the armor can be sharp and can nick the wire insulation if you're not careful.By combining the right tools with good technique and a little patience, you can significantly reduce the frustration of untwisting MC/BX cable wires. Good luck! Flag for review